CASE-IH > BALERS > SQUARE BALERS > IH > (57) - INTERNATIONAL HARVESTER RECTANGULAR BALER (1/57-12/72)

(3) - INTRODUCTION (4) - INTRODUCTION - CONTINUED (A-01) - 57 BALER, TWINE AND WIRE, SERIAL NUMBER 501G AND UP (A-02) - 57 BALER, TWINE AND WIRE, SERIAL NUMBER 501G AND UP (A-05) - MAIN FRAME (A-06) - HITCH (A-07) - MAIN DRIVE SUPPORT (A-08) - LEFT AND RIGHT WHEELS (A-09) - LEFT BALE CHAMBER SIDE (A-10) - RIGHT BALE CHAMBER SIDE (A-11) - LOWER TENSION CHANNEL AND BALE CHAMBER EXTENSION (A-12[A]) - LIFTING JACK, 2598L UP (A-12) - LIFTING JACK (A-13) - BOTTOM PLATE, PLUNGER STOP AND NEEDLE GUARDS (A-14[A]) - CRANKSHAFT AND PITMAN (A-14) - FLYWHEEL AND FLYWHEEL HUB (A-15) - PLUNGER (A-16) - FEED OPENING TOP SHEET (A-17) - MAIN DRIVE (A-18) - PACKER DRIVE (A-19) - PACKER CRANK, FINGERS AND RELIEF (A-20) - CROSS CONVEYOR PLATFORM (A-21) - AUGER AND AUGER DRIVE (A-22) - PICKUP CYLINDER AND DRIVE (A-25[A]) - PICKUP WHEEL, STEEL (A-25) - PICKUP COVER (A-26) - PICKUP WHEEL, RUBBER, WHEN ORDERED (A-27) - TWINE CHEST AND SUPPORT (A-28[A]) - FOUR COIL WIRE CAN (A-28) - TWO COIL WIRE CAN (A-29[A]) - WIRE NEEDLE GUIDES AND WIRE GUIDES (A-29) - TWINE NEEDLE GUIDES AND TWINE GUIDES (A-30[A]) - WIRE NEEDLES AND NEEDLE PITMAN (A-30) - TWINE NEEDLES AND NEEDLE PITMAN (A-31) - KNOTTER BASE PLATE (A-32) - TWISTER BASE PLATE AND DRIVE FRAME (A-34) - KNOTTER AND KNOTTER SHAFT (A-37) - TWISTER AND TWISTER SHAFT (A-39[A]) - BALE LENGTH CONTROL (A-39) - KNOTTER OR TWISTER COVER (A-40) - WARNING LAMP BRACKET AND SOCKET (A-41) - MANUAL TENSION DEVICE (A-42) - HYDRAULIC BALE TENSION DEVICE, CHANNELS, HOSE AND DRIVE (A-44) - HYDRAULIC BALE TENSION DEVICE, HYDRAULIC PUMP AND RESERVOIR (A-45[A]) - POWER TAKE-OFF ATTACHMENT HITCH (A-45) - HYDRAULIC BALE TENSION DEVICE, HYDRAULIC JACK (A-46) - POWER TAKE-OFF ATTACHMENT, GEAR BOX AND PULLEY (A-47) - POWER TAKE-OFF ATTACHMENT, DRIVE SHAFTS FOR 540 AND 1000 RPM (A-49) - POWER TAKE-OFF ATTACHMENT, IDLER PULLEY AND LEVER (A-50) - POWER TAKE-OFF ATTACHMENT, PLUNGER CRANK AND PULLEY SHIELDS (A-51) - PARTS COMMON TO C-123 AND WISCONSIN ENGINES (A-52) - ADDITIONAL PARTS FOR C-123 AND WISCONSIN ENGINES, BATTERY BOX AND ELECTRICAL CABLES (A-53) - ADDITIONAL PARTS FOR C-123 ENGINE, ENGINE MOUNTS AND IDLER (A-54) - ADDITIONAL PARTS FOR WISCONSIN ENGINE, ENGINE BASE AND PULLEYS (A-55[A]) - FLYWHEEL SHIELD (A-55[B]) - DUAL WHEEL (A-55) - PLUNGER CRANK SHIELD, FOR ENGINE DRIVE BALERS (A-56[A]) - BALE CHUTE (A-56) - TRAILER HITCH (A-57) - ENGINE SHUT-OFF ATTACHMENT, FIBER BAR TYPE, FOR WIRE BALER, WHEN ORDERED (A-58) - ENGINE SHUT-OFF ATTACHMENT, PUSH BUTTON TYPE, FOR WIRE BALER, WHEN ORDERED (A-59) - CENTRALIZED LUBRICATION, VALVES (A-60) - CENTRALIZED LUBRICATION, FOR TWINE BALERS, VALVES, TUBING, AND FITTINGS (A-62) - CENTRALIZED LUBRICATION, FOR WIRE BALERS, VALVES, TUBING, SLEEVES AND FITTINGS (A-64[A]) - FUEL TANK AND CONNECTIONS (A-64) - CENTRALIZED LUBRICATION, PUMP, PUMP SUPPORT AND MISCELLANEOUS (A-65) - AIR CLEANER & CONNECTIONS (A-66[A]) - INSTRUMENT PANEL AND GOVERNOR CONTROL RODS (A-66) - RADIATOR AND CONNECTIONS (A-67[A]) - GENERATOR AND CONNECTIONS 6 VOLT ELECTRICAL SYSTEM (A-67) - OIL PRESSURE INDICATOR AND CONNECTIONS (A-68) - GENERATOR AND CONNECTIONS, 12 VOLT ELECTRICAL SYSTEM (A-69) - GENERATOR, DELCO REMY, 6 VOLT (A-70) - GENERATOR, DELCO REMY, 12 VOLT (A-71) - CRANKING MOTOR, DELCO REMY, 6 VOLT (A-72) - CRANKING MOTOR, DELCO REMY, 12 VOLT (A-73) - ELECTRIC STARTING, 6 VOLT ELECTRICAL SYSTEM (A-74) - ELECTRIC STARTING, 12 VOLT ELECTRICAL SYSTEM (A-75) - HOOD, SCREEN AND SUPPORTS (A-76) - BELT PULLEY GEAR REDUCTION DRIVE UNIT