CASE-IH > BALERS > SQUARE BALERS > IH > (430) - INTERNATIONAL HARVESTER RECTANGULAR BALER (NORTH AMERICA) (1/70-12/78)

(3) - INTRODUCTION (4) - INTRODUCTION - CONTINUED (E-01) - 430 AND 440 TWINE AND WIRE BALER (E-04) - HITCH (E-05) - BALE CHAMBER (E-06) - MAIN FRAME (E-07) - WHEELS AND AXLE, FLOTATION TIRES (E-08) - WHEELS AND AXLES (E-09) - CROSS CONVEYOR AND FEED OPENING (E-12) - AUGER AND AUGER DRIVE SUPPORT (E-14) - PICKUP CYLINDER AND DRIVE (E-17) - CUSTON PICKUP CYLINDER (E-18) - PICKUP COVER (E-19) - PICKUP WHEEL, RUBBER, REGULAR FOR 440, WHEN ORDERED FOR 430 (E-20) - MAIN DRIVE (E-22) - PLUNGER (E-24) - PLUNGER CENTER FILLER PACKAGE (E-25) - PACKER FINGERS AND DRIVE - 430 BALER (E-28) - NEEDLE AND NEEDLE GUARD, FOR TWINE BALERS (E-30) - NEEDLES AND GUIDES, FOR WIRE BALERS, SERIAL NUMBER, 430W 50 IN. THRU 001193, 440W 50 IN. THRU 002159 (E-32) - NEEDLES AND GUIDES, LOCK TWIST BALER, SERIAL NUMBER, 430W 001194 & UP, 440W 002160 & UP (E-34) - TWINE CHEST (E-35) - KNOTTER DRIVE FRAME AND BREAST PLATE, FOR TWINE BALERS (E-37) - KNOTTER & KNOTTER COVER, FOR TWINE BALERS, 430T BALER 501N THRU 005755, 440T BALER 501N THRU 002159 (E-39) - KNOTTER DISK PACKAGE, FOR TWINE BALERS (E-40) - KNOTTER, ALL TWINE, SERIAL NUMBER, 430T 005756 & UP, 440T 002160 & UP (E-42) - KNOTTER AND RELATED PARTS, SERIAL NUMBER, 430T 005756 & UP, 440T 002160 & UP (E-44) - TWISTER BASE PLATE & SUPPORTS, WIRE BALERS, S/N, 430T 50 IN. THRU 001193, 440T 50 IN. THRU 002159 (E-46) - TWISTER BASE PLATE AND SUPPORTS, SERIAL NUMBER, 430W 001194 & UP, 440W 002160 & UP (E-48) - TWISTER & TWISTER COVER, WIRE BALERS, S/N 430W 50 IN. THRU 001193, 440W 50 IN. THRU 002159 (E-50) - LOCK-TWIST TWISTER, SERIAL NUMBER, 430W 001194 & UP, 440W 002160 & UP (E-51) - LOCK-TWIST TWISTER AND RELATED PARTS, SERIAL NUMBER, 430W 001194 & UP, 440W 002160 & UP (E-53) - BALE LENGTH CONTROL (E-54) - BALE COUNTER (E-55) - MANUAL BALE TENSION DEVICE, WHEN ORDERED (E-56) - SMV EMBLEM AND LIGHT BRACKET SOCKET (E-57) - HYDRAULIC BALE TENSION DEVICE CHANNELS,, HOSE AND DRIVE FOR AUTOMATIC LUBRICATION (E-59) - HYDRAULIC BALE TENSION DEVICE HYDRAULIC PUMP AND RESERVOIR, WHEN ORDERED (E-61) - HYDRAULIC BALE TENSION DEVICE HYDRAULIC JACK, WHEN ORDERED (E-62) - POWER TAKE-OFF DRIVE SHAFT CLUTCH, WHEN ORDERED (E-63) - POWER TAKE-OFF DRIVE SHAFT CLUTCH, WHEN ORDERED (E-64) - POWER TAKE-OFF DRIVE SHAFTS, THREE KNUCKLE (E-66) - POWER TAKE-OFF DRIVE SHAFTS, TWO KNUCKLE, FOR 430 BALER, WHEN ORDERED (E-68) - WISCONSIN ENGINE ATTACHMENT, ENGINE AND ENGINE MOUNTING PARTS (E-70[A]) - TWO COIL WIRE CONTAINER FOR WIRE BALERS WHEN ORDERED (E-70) - WISCONSIN ENGINE ATTACHMENT ELECTRICAL SYSTEM, 12 VOLT, WHEN ORDERED (E-71[A]) - ENGINE SHUT-OFF ATTACHMENT FOR WIRE BALERS, WHEN ORDERED (E-71) - FOUR COIL WIRE CONTAINER, FOR WIRE BALERS, WHEN ORDERED (E-72[A]) - BALE CHUTE ATTACHMENT, WHEN ORDERED (E-72) - TRAILER HITCH ATTACHMENT, WHEN ORDERED (E-73[A]) - RIGHT DUAL WHEEL ATTACHMENT, WHEN ORDERED (E-73[B]) - FLYWHEEL AND BELT SHIELD, WHEN ORDERED (E-73[C]) - FLYWHEEL AND KNUCKLE SHIELD (E-73) - LEFT DUAL WHEEL ATTACHMENT, WHEN ORDERED (E-74[A]) - PLUNGER CRANK SHIELD ATTACHMENT FOR ENGINE DRIVE ONLY (E-74) - PLUNGER CRANK SHIELD ATTACHMENT, POWER TAKE-OFF DRIVE ONLY (E-75) - LIFTING JACK (E-76) - AUTOMATIC LUBRICATION ATTACHMENT (E-77) - AUTOMATIC LUBRICATION ATTACHMENT VALVES, TUBING & FITTINGS - FOR TWINE BALERS ONLY (E-79) - AUTOMATIC LUBRICATION ATTACHMENT VALVES, TUBING & FITTINGS - FOR WIRE BALERS ONLY (E-81[A]) - NEEDLE GUARD ATTACHMENT WHEN ORDERED (E-81) - BALE TURNER ATTACHMENT, WHEN ORDERED (E-82) - AUTOMATIC LUBRICATION ATTACHMENT, PUMP AND TIMER