| № | Номер | Название | Опции | Альт |
|---|
| 1 | NSS | NOT SOLD SEPARAT | HOUSING - range gear, see Fig. 6-12 for ordering and for range inlet cover | |
| 2 | B17428 | LOCTITE | SEALANT - Gasket Eliminator No. 504, 50 ml tube, range gear housing to transmission housing, not shown | |
| 3 | 166-46 | 12 PT SCREW,Flg, 3/8" - 16 x 1 1/4", Gr 8 | BOLT - Ferry head, 3/8" - 16 NC x 1-1/4" | |
| 4 | D32117 | COPPER WASHER | WASHER, COPPER, 3/8" | |
| | Part of Seal Kit, P/N G102662 | | |
| 5 | A50094 | PLUG,Screw, 5/8" - 18 x 0.377" | - range selector detent | |
| 6 | A50093 | SEALING WASHER | WASHER - special, detent plug | |
| | Part of Seal Kit, P/N G102662 | | |
| 7 | A50092 | SPRING | - detent | |
| 8 | 211-214 | BALL,1/2" Dia | - steel, meter 1/2" Dia | |
| 9 | 131-91 | LOCK NUT,3/4"-16, G8 | NUT - hex, self-locking, 3/4" - 14 NF, plated | |
| 10 | 32601 | WASHER | - special, yoke retaining | |
| 11 | 34395 | SEALING WASHER | WASHER - yoke seal | |
| | Part of Seal Kit, P/N G102662 | | |
| 12 | G106153 | YOKE | - to drive shaft | |
| 13 | A50420 | SEAL | - input shaft | |
| | Part of Seal Kit, P/N G102662 | | |
| 14 | G105118 | OIL SEAL | - selector shaft, double lip | |
| | Part of Seal Kit, P/N G102662 | | |
| 15 | R13804 | RING | SNAP RING - bearing | |
| 16 | A26537 | BALL BEARING,34.99mm ID x 80mm OD x 21mm W | - input shaft | |
| 17 | G100307 | GEAR | DRIVE GEAR - input shaft, high range | |
| 18 | R15364 | SNAP RING,#152, 1.527", Ext | - drive gear | |
| 19 | G106413 | GEAR | INPUT SHAFT - 15 gear teeth, use with G100309 low range clutch gear only. Ref. 29, used on all loader models and standard gauge dozer models; used on some LGP dozer models | |
| 19 | A50365 | SHAFT | INPUT SHAFT - 17 gear teeth, use with A50517 low range clutch gear only, Ref. 29, used on some LGP dozer models | |
| 20 | A50077 | BEARING CONE,1.1811" ID x 0.748" | RACE - roller bearing, inner | |
| 21 | A50255 | BEARING, ROLLER, CYL,2.8359" OD x 0.748" | ROLLER BEARING - input shaft | |
| 22 | A27417 | RING | SNAP RING - roller bearing | |
| 23 | A50258 | ROLLER BEARING,3.1510" OD x 0.8268" | - main shaft, front | |
| 24 | A50332 | BEARING CONE,1.25" ID x 0.8268" | RACE - roller bearing, inner | |
| 25 | A50333 | WASHER | THRUST WASHER - drive gear, front | |
| G102662 | SEAL | KIT - seal, Includes: Ref. 4, 6, 11, 13 and 14, for complete kit see Figure 6-66 | |
| 26 | G100308 | GEAR | DRIVEN GEAR - high range clutch, on main shaft, 24 teeth | |
| 27 | A51806 | COLLAR | SLEEVE - sliding, range selector | |
| 28 | A50502 | COLLAR | - sliding, sleeve to main shaft, range selector | |
| 29 | G100309 | GEAR | DRIVEN GEAR - low range clutch, 28 teeth, use with G106413 input shaft only, Ref. 19, used on all loader models and standard gauge dozer models; used on some LGP dozer models | |
| 29 | A50517 | GEAR | DRIVEN GEAR - low range clutch, 39 teeth, use with A50365 input shaft only, Ref. 19, used on some LGP dozer models | |
| 30 | A50071 | WASHER | THRUST WASHER - driven gear, rear | |
| 31 | A26946 | RING | SNAP RING - gear | |
| 32 | G107672 | SHAFT | - range selector, with welded fork | |
| 33 | 138-68 | LOCK PIN,5/32" x 7/16", Slotted | PIN, , Range gear 5/32" x 7/16", Slotted | |
