CASE > HEAVY EQUIPMENT > CRAWLER DOZERS > 300 > (310C) - CASE CRAWLER TRACTOR (S/N 3008188 TO 3010989) (1/59-12/90) > (07) - HYDRAULIC SYSTEM > (094) - LOADER FRAME, LIFT ARM, BUCKETS, AND CYLINDERS

№ Номер Название Опции Альт 1 D21281 FRAME - main, loader 2 D23870 BUSHING - main arm pivot 3 D20685 SPACER - main frame, rear 4 14-1048 BOLT,Hex, 5/8" - 18 x 3", Gr 5 HHCS - 5/8 - 18 NF x 3 5 92-10 LOCK WASHER,5/8" WASHER, LOCK, 5/8" 6 25-1110 NUT,5/8"-18, G5 - hex. (5/8 - 18 NF) 7 14-1036 BOLT,Hex, 5/8" - 18 x 2-1/4", Gr 5 8 14-1236 BOLT,Hex, 3/4" - 16 x 2-1/4", Gr 5, Full Thd HHCS - 3/4 - 16 NF x 2-1/4 9 92-12 LOCK WASHER,3/4" WASHER, LOCK, 3/4" 10 25-1112 NUT,3/4"-16, G5 - hex. (3/4 - 16 NF) 11 219-1 LUBE NIPPLE,1/8" - 27 NPTF FITTING - grease, straight (1/8" NPT) 12 D23190 PLATE - rub and reinforcement, lower 13 D23189 PLATE - rub and reinforcement, upper 14 164-73 HEX SOC SCREW,Flat Hd, 1/2" - 13 x 1 1/2" SCREW - cap, socket head (1/2" - 13 NC x 1-1/2") 15 D23332 X NUT - lock (1/2" - 13 NC) 16 31636 BLOCK - stop 17 31123 BRACKET - mounting, stop block 18 14-856 BOLT,Hex, 1/2" - 20 x 3-1/2", Gr 5 HHCS - 1/2 - 20 NF x 3-1/2 19 230-4618 LOCK NUT,1/2"-20, GA NUT - lock (1/2" - 20 NF) 20 D23301 ARM - main (42" gauge loader only) Includes 2 - D21912 bushings and 8 - 30634 bushings D23156 ARM - main (48" gauge loader only) 21 D21912 BUSHING - bucket pivot, main arm 22 30634 BUSHING,32.05mm ID x 38.18mm OD x 17.6mm L - bucket linkage pivot, main arm 23 219-55 LUBE NIPPLE,90 Degree Elbow, 1/8" - 27 NPTF NIPPLE, LUBE, 90º, 1/8" NPT x .84" lg 24 31318 SHAFT - pivot, main arm 25 14-888 HHCS - 1/2 - 20 NF x 5-1/2 26 230-4618 LOCK NUT,1/2"-20, GA NUT - lock (1/2" - 20 NF) 27 31608 CYLINDER - Loader lift, hydraulic (R.H.) See figure 102 for breakdown 28 31609 CYLINDER - Loader lift, hydraulic (L.H.) See figure 102 for breakdown 29 31109 PIN ASSY. PIN - mounting, lift cylinder (Rear) 30 14-816 BOLT,Hex, 1/2" - 20 x 1", Gr 5 HHCS - 1/2 - 20 NF x 1 31 92-8 LOCK WASHER,1/2" Use 193-32 and D23740 1/2" 193-32 LOCK WASHER,Int Tooth, 1/2" WASHER, LOCK, , Not shown Int Tooth, 1/2" D23740 BUSHING - lockhead pin (Not shown) 32 31340 PISTON PIN - mounting, lift cylinder (Front) 33 14-816 BOLT,Hex, 1/2" - 20 x 1", Gr 5 HHCS - 1/2 - 20 NF x 1 34 92-8 LOCK WASHER,1/2" Use 193-32 and D23740 1/2" 193-32 LOCK WASHER,Int Tooth, 1/2" WASHER, LOCK, , Not shown Int Tooth, 1/2" D23740 BUSHING - lockhead pin (Not shown) 70549 LEVER - pivot, bucket cylinder and leveling rod (When stock is exhausted, order 72619 and 72620) 35 72619 LEVER - pivot, R.H. (Bucket cylinder and leveling rod) See 70549 36 72620 LEVER - pivot, L.H. (Bucket cylinder and leveling rod) See 70549 37 31146 SPACER - 72619 and 72620 pivot levers 38 14-1692 HHCS - 1 - 14 NF x 5-3/4 39 131-370 LOCK NUT NUT - lock (1" - 14 NF) 40 34276 ROD - leveling 41 30634 BUSHING,32.05mm ID x 38.18mm OD x 17.6mm L - leveling rod 42 219-1 LUBE NIPPLE,1/8" - 27 NPTF FITTING - grease, straight (1/8" NPT) 43 31147 BOLT - pivot, leveling rod 44 30959 SPACER - leveling rod pivot bolt 45 95-16 WASHER,1 1/16" x 2 1/2" x .164" - standard wrot (1") 46 131-370 LOCK NUT NUT - lock (1" - 14 NF) 47 D23808 CYLINDER - bucket, hydraulic (See figure 104 for breakdown) 48 31146 SPACER - bucket cylinder pivot, rear 49 14-1692 HHCS - 1 - 14 NF x 5-3/4 50 131-370 LOCK NUT NUT - lock (1" - 14 NF) 51 30957 LEVER - pivot, bucket dump arm and bucket cylinder 52 30959 SPACER - pivot, lower (30957 pivot lever) 53 14-1664 BOLT,Hex, 1" - 14 x 4", Gr 5 HHCS - dump arm and pivot lever mounting (1 - 14 NF x 4) 54 131-370 LOCK NUT NUT - lock (1" - 14 NF) 55 30959 SPACER - pivot, bucket cylinder (Front) 56 14-1664 BOLT,Hex, 1" - 14 x 4", Gr 5 HHCS - 1 - 14 NF x 4 57 131-370 LOCK NUT NUT - lock (1" - 14 NF) 58 34273 ARM - bucket dump, R.H. (42" gauge loader only) Includes ref. numbers 60 and 61 34269 WASHER ARM - bucket dump, R.H. (48" gauge loader only) Includes ref. numbers 60 and 61 59 34274 ARM - bucket dump, L.H. (42" gauge loader only) Includes ref. numbers 60 and 61 34270 BELT ARM - bucket dump, L.H. (48" gauge loader only) 60 30634 BUSHING,32.05mm ID x 38.18mm OD x 17.6mm L - dump arm, rear 61 31148 BUSHING - dump arm, front (When stock is exhausted, order D21903) D21903 BUSHING - dump arm, front (See 31148) 62 219-1 LUBE NIPPLE,1/8" - 27 NPTF FITTING - grease, straight (1/8" NPT) 63 30959 SPACER - pivot, dump arm (Rear) 64 31068 SPACER - pipe 65 33965 SPACER ROD - tie 66 131-370 LOCK NUT NUT - lock (1" - 14 NF) 67 32648 LINE BUCKET - Loader (42" gauge loader only) 68 31258 EDGE - cutting, bucket 69 46-826 RIVET - cutting edge 67 32649 BUCKET - Loader (48" gauge loader only) 68 30889 EDGE - cutting, bucket 69 46-826 RIVET - cutting edge 70 32599 PIN - mounting, bucket to main arm 71 14-864 CAPSCREW,Hex, 1/2" - 20 x 4", Gr 5 HHCS - 1/2 - 20 NF x 4 72 230-4618 LOCK NUT,1/2"-20, GA NUT - lock (1/2" - 20 NF) 73 32598 PIN - mounting, bucket to bucket dump arm 74 14-660 SCREW,Hex, 3/8" - 24 x 3 3/4", Gr 5 HHCS - 3/8 - 24 NF x 3-3/4 75 230-4616 LOCK NUT,3/8"-24, GA NUT - lock (3/8" - 24 NF) 76 31928 SHIM - bucket to dump arm (When stock is exhausted, order O1550L) 01550L SHIM - bucket to dump arm (See 31928) 77 16988 TOOTH - digging (Optional) 78 14-836 BOLT,Hex, 1/2" - 20 x 2-1/4", Gr 5 HHCS - 1/2 - 20 NF x 2-1/4 79 92-8 LOCK WASHER,1/2" 80 25-118 NUT,1/2"-20, G5 - hex. (1/2 - 20 NF) 81 D20370 COVER - access, instrument panel back