Каталоги  Вход

CASE > HEAVY EQUIPMENT > CRAWLER EXCAVATORS > 1100 > (1187C) - CASE FELLER/BUNCHER CRAWLER EXCAVATOR (1/89-12/92) > (04) - ELECTRICAL SYSTEMS > (4-14) - ELECTRICAL HARNESS - CAB AND TURNTABLE

№НомерНазваниеОпцииАльт
1S618923HARNESS- turntable, Includes: Ref. 2 - 4
2S120488CONNECTOR,ELECTRICCONNECTOR - electrical, harness
P/N S120488 is a 9 pin recepticle, 8 pins around the edges and one big one in the middle.
3S99523CONNECTOR, ELECPLUG - connector, not shown
3aS107261PLUG- connector, not shown
4R14668CLAMP- harness, rear
5T50103CLAMP- harness, front
6A61275CLIPCLAMP - horn wire
7131-52NUT,3/8"-16, GCNUT - light hex, self-locking, 3/8 inch NC
8495-11041WASHER,0.406" ID x 0.812" OD x 0.065" W(Flat, 13/32 x 13/16 x 1/16") 3/8", SAE
9S242833HARNESSWIRE - diode
10S117294ROD, CONNECTINGCONNECTOR - solenoid control valve wires
11S516951VALVEASSEMBLY - control, solenoid, parts list Figure 8-56
12S616066FILTERASSEMBLY - hydraulic oil, parts list Figure 8-70
D134737IGNITION SWITCHSWITCH ASSEMBLY - key, electrical system, Includes: Ref. 13 and 14
13NSSNOT SOLD SEPARATSWITCH - key, electrical system
14A77313SET OF 2 KEYSKEYS - switch, set of two keys; metal without padding
15S242795PLATE- switch mounting
16142-102SCREW,Cross Oval Hd, #10 - 24 x 3/4"- machine, oval head Phillips, No. 10 NC x 3/4 inch
17F64315WASHER- special finishing, No. 10, not shown
18131-143SPRING NUT,Tinn, U, #10-24
19D77650HORN- electrical
20L73799BRACKET- horn mounting
21L30866LOCK NUT- horn mounting
22413-516BOLT,Hex, 5/16" - 18 x 1", Gr 5- hex, 5/16 NC x 1 inch
23231-1445NUT,5/16"-18, GBNUT - hex, self-locking, 5/16 inch NC
24S516994GAUGEHOURMETER - electric
25S118430SWITCH- heater, supplied with heater, see Figure 4-26, Ref. 24
26S242826HEATERASSEMBLY - cab, parts list Figure 4-26
27S242036SWITCHASSEMBLY - collector, includes wire, used on models with collector
28515-2363CLAMP,M6.3, Insul, 3/8" Bolt- collector switch and wire, used on models with collector
29413-616BOLT,Hex, 3/8" - 16 x 1", Gr 5- hex, 3/8 NC x 1 inch, Used on models with collector
30495-11041WASHER,0.406" ID x 0.812" OD x 0.065" W(Flat, 13/32 x 13/16 x 1/16"), Used on models with collector 3/8", SAE
31131-52NUT,3/8"-16, GCNUT - light hex, self-locking, 3/8 inch NC, used on models with collector
32S119987GRIP- left control lever, see Figure 9-4 for hand lever controls
33L18337CABLE TIE,9.95"-12.1" lgSTRAP - tie, 15 inch, nylon
34S119525CABLE- 29.17 ft (8.89 m) long, collector to control valve, cut from S118482X bulk cable, see below, used on models with collector
35223-61TERMINAL CONNECTOR,14 - 16TERMINAL - eyelet, 14-16 wire x 3/8 inch screw size, cable at solenoid control valve, used on modes with collector
36223-92TERMINALTERMINAL - female, 14-16 wire size, cable at solenoid valve, used on models with collector
37S516409VALVEASSEMBLY - control, solenoid, parts list Figure 8-58, used on models with collector
38515-23190CLAMP,3/4", Insul, 3/8" Bolt- diode to monoblock valve
39S77322CLAMP- harness
40L115883RELAY- starter and cab
4193-81000LOCK WASHER,Int Tooth, #10WASHER - internal tooth lock, No. 10
42495-31022WASHER,#10
43225-14110NUT,#10-24
44S242611ALARMBUZZER - low engine oil pressure
4593-21014LOCK WASHER,Ext Tooth, #6WASHER - internal tooth lock, No. 6, not shown
S118482XCABLE- bulk, 600 inch (15.24 m) long, 2 wire, 14 gauge