| № | Номер | Название | Опции | Альт |
|---|
| 1 | D141275 | HARNESS | engine, main, without fuse block in harness on right hand side of engine, starter relay mounts on chassis upright, used on models without electronic instrument control center | | | | See Figure 04-114 for special parts used on models with electronic instrument control center. | | | | 2 | D39696 | CLAMP,25.40mm - 13.49mm Bolt, CTD | double, harness | | | 3 | 113-205 | BOLT,Hex, 3/8" - 16 x 5/8", Gr 5 | | | | 4 | 192-21 | LOCK WASHER,3/8" | WASHER, LOCK, 3/8" | | | 5 | 25-226 | SQUARE NUT,Sq, 3/8"-16 | square, 3/8"-16 NC | | | 6 | D128310 | RELAY | starter, 30 amperes | | | | 40 amperes is marked on the relay. This is the resistance rating. The inductive rating is 30 amperes. We use this inductive rating in our literature. | | | | 7 | 187-576 | SELF-TAP SCREW,Hex Wash Hd, #10 x 3/8" | SCREW self tapping, No. 10-24 x 3/8" | | | 8 | D140282 | SUPPORT | PLATE relay mounting | | | 9 | 113-206 | BOLT,Hex, 3/8" - 16 x 3/4", Gr 5, Full Thd | | | | 10 | 192-21 | LOCK WASHER,3/8" | WASHER, LOCK, 3/8" | | | 11 | 25-226 | SQUARE NUT,Sq, 3/8"-16 | square, 3/8"-16 NC | | | 12 | D88052 | CLAMP,25.4mm ID, 10.31mm Bolt Hole, P Type | P-type, harness, uses existing loader hydraulic line hardware, if used, may be replaced by tie straps | | | 13 | L71879 | DIODE ELEMENT,400V, 3A | DIODE harness, at power shuttle | | | 14 | D47783 | CLAMP | double, harness and power wire, uses existing steering hydraulic tube hardware | | | 14a | A141013 | CLAMP,1 1/8", Insul, 3/8" Bolt | P-type | | | 15 | 49838 | CLAMP | P-type, harness, uses existing hardware, may be replaced by tie straps | | | 16 | L18337 | CABLE TIE,9.95"-12.1" lg | STRAP tie, nylon, harness, 15" | | | 17 | 193-60 | LOCK WASHER,Int Tooth, 1/4" | WASHER, LOCK, Int Tooth, 1/4" | | | 18 | 825-1106 | NUT,Hex, M6, Cl 8 | hex, 6 mm-1, plated | | | 19 | A166057 | TEMPERATURE SENDER,1/2" - 14 NPTF | SENDER engine water coolant temperature | | | 20 | 193-1000 | NUT,Keps, w/LW,#10-32 | AND LOCK WASHER, No. 10-32 NF, plated | | | 21 | 49838 | CLAMP | P-type, harness, left hand side of engine, front clamps use existing hardware | | | 22 | 515-23127 | CLAMP,1/2", Insul, 3/8" Bolt | P-type, harness, uses existing engine hardware | | | 23 | A162297 | SWITCH | - Oil Pressure Sender, Used on Models Without Electronic Instrument Control Center; See Figure 4-114 for Special Parts Used on Models With Electronic Instrument Control Center | | | 24 | L103131 | INDICATOR | SENDER air filter restriction indicator | | | 25 | 221-1335 | COUPLING,Pipe, 1/8" NPT | | | | 26 | D36264 | FITTING | ADAPTER special, includes safety filter | | | 27 | 515-23190 | CLAMP,3/4", Insul, 3/8" Bolt | P-type, harness, uses existing hardware | | | 27a | 515-23143 | CLAMP,9/16", Insul, 3/8" Bolt | P-type, 38467 tube beneath backhoe control valve | | | 28 | D141119 | ELECTRICAL WIRE | WIRE power, starter to side console harness fuse block in floor, used with Ref. 1 harness | | | 29 | D141118 | GROMMET | power wire | |
|
|