| № | Номер | Название | Опции | Альт |
|---|
| 1 | D93335 | FRAME | - backhoe mounting, see Figure 9-28 for bushings | |
| 2 | REF | INSTRUCTION | CYLINDER ASSEMBLY - backhoe swing, see parts list Figures 8-68 or 8-70 | |
| 3 | D94401 | SUPPORT | - swing cylinders, Includes: Ref. 4 | |
| 4 | D60159 | BUSHING,60.55mm ID x 69.85mm OD x 38.1mm L | - support | |
| 5 | 413-1648 | BOLT,Hex, 1" - 8 x 3", Gr 5 | | |
| 6 | 113-945 | BOLT,Hex, 1" - 8 x 5-1/2", Gr 5 | - hex, 1 NC x 5-1/2 inch, special thread length | |
| 7 | D36505 | WASHER,26.99mm ID x 47.63mm OD x 2.38mm Thk | - hardened, 1 inch | |
| 8 | D94229 | LARGE PLATE | RETAINER - nut | |
| 9 | 129-568 | NUT,Sq, 1"-8, G5 | - square, 1 inch NC | |
| 10 | D90057 | COVER | - vinyl, bolt | |
| 11 | D90868 | LATHE | TOWER - swing, without inner ears, uses (1) boom mtg pin and Ref. 21 - 26 for mtg swing cylinder, see Ref. 16, see Figure 9-34 for boom attaching parts, Includes: Ref. 12 - 15 | |
| | When ordering a new D90868 swing tower, two D88985 pins (Ref. 21) and one D94031 plate (Ref. 23) must also be ordered, unless these Refs. are already installed. | | |
| 12 | D49429 | BUSHING | - at boom cylinder | |
| 13 | D91241 | BUSHING,51.02mm ID x 69.88mm OD x 60mm L | - boom mounting | |
| 14 | D94018 | BUSHING,44.58mm ID x 53.98mm OD x 30mm L | - swing cylinder mounting, if used | |
| 15 | D90863 | WASHER,58.35mm ID x 130mm OD x 6mm Thk | Washer - Bearing, welded to bottom of some swing towers, not used when Ref. 28 is used 6mm Thk | |
| 16 | D127544 | FRAME | TOWER - swing, 2-1/8 inch OD bushings at swing cylinder mtg holes, with inner ears, uses (2) boom mtg pins & Ref. 21 - 26 for mtg swing, see Ref. 11, see Figure 9-34 for boom attaching parts | |
| | No longer available. For service order D136868 swing tower, (2) R57306 pins, (4) D25280 snap rings, & (4) 495-81226 washers on Fig. 9-32, Ref. 43 - 45 | | |
| 17 | D49429 | BUSHING | - at boom cylinder | |
| 18 | D33023 | BUSHING,51.02mm ID x 63.5mm OD x 50.8mm L | - outer ears, boom mounting | |
| 19 | D38943 | BUSHING,51.02mm ID x 63.5mm OD x 28.6mm L | - inner ears, boom mounting | |
| 20 | D94018 | BUSHING,44.58mm ID x 53.98mm OD x 30mm L | - 2-1/8 inch OD, swing cylinder mounting | |
| 21 | D88985 | PIN,44.45mm OD x 181.5mm L | - swing cylinder to swing tower, 7-1/8 inch (181 mm) long, used with item 11 or 16 swing tower, if used | |
| | When ordering a new D90868 swing tower, two D88985 pins (Ref. 21) and one D94031 plate (Ref. 23) must also be ordered, unless these Refs. are already installed. | | |
| 22 | D94019 | PIN,44.4mm OD x 196.5mm L | - swing cylinder to swing tower, 7-3/4 inch (197 mm) long, used with Ref. 11 or 16 swing tower, if used | |
| | When ordering a new D90868 swing tower, two D88985 pins (Ref. 21) and one D94031 plate (Ref. 23) must also be ordered, unless these Refs. are already installed. | | |
| 23 | D94031 | PLATE | - pin retaining, 6-3/8 inch (162 mm) long, mounts between pins, used with Ref. 11 or 16 swing tower | |
| | When ordering a new D90868 swing tower, two D88985 pins (Ref. 21) and one D94031 plate (Ref. 23) must also be ordered, unless these Refs. are already installed. | | |
| 24 | 413-816 | BOLT,Hex, 1/2" - 13 x 1", Gr 5 | Used with item 11 or 16 swing tower Hex, 1/2"-13 x 1", G5, Full Thd | |
| 25 | 80679 | LOCK WASHER,1/20.507 CST ZND | WASHER, LOCK, , Used with item 11 or 16 swing tower 1/2" | |
| 26 | D64050 | WASHER | - flat, 1/2 inch, used with item 11 or 16 swing tower | |
| 27 | D120495 | PIN | - tapered, swing tower to backhoe frame, lower, Ref. 29 grease fitting mounts in bottom of pin, no longer used, order D123653 pin (Ref. 27A) | |
| 27a | D123653 | PIN,57.15mm OD x 140mm L | - tapered, swing tower to backhoe frame, lower, Ref. 29 grease fitting mounts in top of pin | |
| 28 | D89338 | SPACER | - bearing, if used, not used when Ref. 15 is used | |
| 29 | 219-1 | LUBE NIPPLE,1/8" - 27 NPTF | FITTING - grease, straight, 1/8 PT x 21/32 inch | |
| 30 | D120610 | NUT | - hex, 1-3/4 inch NF, special | |
| 31 | D90576 | PIN | - lock, backhoe swing | |
| 32 | D33805 | PIN | - self-locking | |
| 33 | D90727 | PIN,57.15mm OD x 198mm L | - swing tower to backhoe frame, upper | |
| 34 | 413-840 | BOLT,Hex, 1/2" - 13 x 2-1/2", Gr 5 | - hex, 1/2 NC x 2-1/2 inch | |
| 35 | 495-11053 | WASHER,1/2", SAE | (17/32" x 1-1/16" x 3/32") 1/2", SAE | |
| 36 | 131-70 | NUT,1/2"-13, GB | NUT - light hex, self-locking, 1/2 inch NC | |
| 37 | D74249 | WASHER,60mm ID x 120mm OD x 2mm Thk | SPACER - bearing, 5/64 inch (2 mm) thick | |
| 38 | D136868 | FRAME | TOWER - swing, 2-1/4 inch O.D. bushings at swing cylinder mounting holes, with inner ears, uses two boom mounting pins and Ref. 43 - 45 for mounting swing cylinder, see Figure 9-34 for boom attaching parts | |
| 39 | D49429 | BUSHING | - at boom cylinder | |
| 40 | D33023 | BUSHING,51.02mm ID x 63.5mm OD x 50.8mm L | - outer ears, boom mounting | |
| 41 | D38943 | BUSHING,51.02mm ID x 63.5mm OD x 28.6mm L | - inner ears, boom mounting | |
| 42 | D37495 | BUSHING,44.76mm ID x 57.15mm OD x 31.75mm L | - 2-1/4 inch O.D., swing cylinder mounting | |
| 43 | R30449 | PIN | - swing cylinder to swing tower, used with item 38 swing tower | |
| 44 | 495-81226 | WASHER,46.02mm ID x 63.5mm OD x 3.35mm Thk | - flat, 1-13/16 x 2-1/2 x 1/8 inch, used with Ref. 38 swing tower | |
| 45 | D25280 | SNAP RING,#175, Ext | Ring, Snap, , R30449 pin, used with ref. 38 swing tower #175, Ext | |
