| № | Номер | Название | Опции | Альт |
|---|
| 1989181C3 | ENGINE ASSEMBLY | ENGINE ASSY ENGINE ASSEMBLY - complete, 4T-390, includes all parts except starter, alternator, fan, fan belt, air cleaner, muffler and exhaust pipe, for service order basic engine below | | | | For correct engine identification make sure that engine part number 1989181C3 is stamped on the engine serial number tag. | | | | 1989092C3 | BASIC ENGINE | includes all parts except starter, alternator, fan & belt, air cleaner, muffler, ex manifold, flywheel & housing, oil fill & dipstick, fuel inj pump, injectors & lines, front pulley, belt tensioner, turbocharger & aftercooler; See Note | | | 1989092C3R | REMAN-BASIC ENGINE | includes all parts except starter, alternator, fan & belt, air cleaner, muffler, ex manifold, flywheel & housing, oil fill & dipstick, fuel inj pump, injectors & lines, front pulley, belt tensioner, turbocharger & aftercooler | | | 1989092C3C | CORE-BASIC ENGINE | Return Part Number | | | AR77758 | BLOCK ASSY. | | | | AC77758 | CORE-ENGINE | Return Part Number - use this part number to return short block core for credit when using a remanufactured assembly | | | J933236 | SHORT ENGINE | BLOCK ASSEMBLY - short, new, includes stripped block, pistons, connecting rods and bearings, crankshaft and bearings, Includes: Ref. 1 - 8 | | | | Order J933220 hardware kit and 250838A2 connector when ordering J933236 block assembly. 250838A2 connector is used for adapting the old oil pressure sender to the new cylinder block. See Figure 4-10 for 250838A2 connector. | | | | | Component parts on this figure do not apply to the remanufactured assembly | | | | JR933236 | REMAN-SHORT ENGINE | | | | JC933236 | CORE-SHORT ENGINE | Return Part Number | | | 1 | 87444172 | BLOCK ASSY. | BLOCK ASSEMBLY - stripped, engine, Includes: Ref. 2 - 8 | | | | Order J933220 hardware kit and 250838A2 connector when ordering J933236 block assembly. 250838A2 connector is used for adapting the old oil pressure sender to the new cylinder block. See Figure 4-10 for 250838A2 connector. | | | | 2 | J900967 | BEARING CAP | CAP - main bearing | | | 3 | J900068 | BEARING WASHER | RING - dowel, 18 mm OD, main bearing, Serial Range: cap-block | | | 4 | J927948 | BOLT,Flng, MJ12 x 1.5H6H x 119mm, Cl 12.9 | SCREW, , Main bearing cap, Special Hex Flg Hd, M12 x 1.5 x 119 | | | 5 | REF | INSTRUCTION | BUSHING - camshaft front, see Figure 2-34, Ref. 2 | | | 6 | A77782 | PLUG | PLUG - expansion, 58 mm OD | | | 6a | A77505 | PLUG | PLUG - hex socket, 3/4 inch PT | | | 7 | J900956 | PLUG | PLUG - expansion, 18 mm OD | | | 8 | 41-1616 | PLUG,Cup, 1", Stainless | PLUG, , Expansion Cup, 1", Stainless | | | J933220 | PACKAGE,SERVICE | KIT - block hardware, Includes: Ref. 9 - 18 | | | | Order J933220 hardware kit and 250838A2 connector when ordering J933236 block assembly. 250838A2 connector is used for adapting the old oil pressure sender to the new cylinder block. See Figure 4-10 for 250838A2 connector. | | | | 9 | J900958 | PLUG | PLUG - expansion, 32 mm OD | | | 10 | J900955 | PLUG | PLUG - expansion, 10 mm OD | | | 11 | 172599 | PLUG,Exp, 2 3/8" | PLUG - expansion, Welch, 60 mm OD | | | 12 | J926047 | O-RING,0.07" Thk x 2.239" ID | O-RING - sealing, 57 mm ID | | | 12a | J920706 | PLUG | PLUG - expansion, 22 mm OD, not used in this application, Ref. 19, J903744 turbocharger oil drain tube is installed in this port | | | 13 | J900257 | PIN,10.01mm OD x 16mm L | PIN - dowel, 16 mm long, locating | | | 14 | J902343 | DOWEL | RING - dowel, 16 mm OD | | | 15 | J900068 | BEARING WASHER | RING - dowel, 18 mm OD | | | 16 | 233426A1 | PLUG,M10 x 1 ORB | PLUG - hex, 10 mm, Includes: Ref. 16A | | | 16a | 637-62081 | O-RING,1.6mm Thk x 8.1mm ID, Cl 6, 90 Duro | O-RING - 8.1 ID x 1.6 mm wide, plug | | | 17 | A77429 | PLUG | PLUG - hex socket, 1/2 inch PT | | | 18 | J930139 | NOZZLE CAP | NOZZLE - piston cooling | | | 19 | J903744 | PIPE FITTING,22.42 mm ID x 28 mm OD x 90.2, 64 mm L | TUBE - turbocharger oil drain | | | 20 | J900267 | SEAL | SEAL - cover bolt | | | 21 | 845-8020 | BOLT,Hvy Hex, M8 x 20mm, Cl 8.8 | BOLT - heavy hex flange, 8-1.25 x 20 mm | | | 22 | J925680 | COVER | COVER - tappet | | | 23 | J928831 | GASKET | GASKET - tappet cover | | | 24 | J907586 | BAFFLE | BAFFLE - tappet cover | | | 25 | J905779 | TUBE,9.52 mm OD x 228 mm L | TUBE - dipstick | | | 26 | J905781 | DIPSTICK | DIPSTICK - oil level gauge | | | 27 | J905440 | TUBE | TUBE - oil fill | | | 28 | J906696 | SEAL,41mm ID x 43mm OD x 2.5mm H | O-RING - 38 mm (1-1/2 inch) ID | | | 29 | 854-12025 | BOLT,Hvy Hex, M12 x 25mm, Cl 10.9 | BOLT - heavy hex flange, 12-1.75 x 25 mm, class 10.9 | | | 30 | A77424 | FILLER CAP | CAP - oil fill tube | | | 31 | J903102 | CONNECTION | CONNECTION - water inlet | | | 32 | J906697 | SEAL,Square, 5.16mm Thk x 50.17mm ID | O-RING - sealing, 50 mm ID | | | 33 | 854-10075 | BOLT,Hvy Hex, M10 x 75mm, Cl 10.9 | BOLT - heavy hex flange, 10-1.5 x 75 mm, class 10.9 | | | 34 | A77429 | PLUG | PLUG - hex socket, 1/2 inch PT | | | 35 | J918612 | TUBE,360.00 mm | Breather | | | 36 | J904230 | CLAMP,25.4mm | CLAMP - spring, hose | | | 37 | J909670 | CLIP | CLIP - retaining | | | 196803A1 | KIT | KIT - engine block heater, Includes: Ref. 38 - 40 | | | 38 | NSS | NOT SOLD SEPARAT | ELEMENT - engine heater, 120 volt | | | 39 | 196466A1 | ELECTRIC CABLE | CABLE - engine block heater | | | 40 | J910517 | O-RING | O-RING - heater sealing | | | 309651A1 | KIT | KIT block heater, new style threaded, Consists of: J940911 Element Assy. (NSS) and 196466A1 Cord, rated at 120V/750W. | |
|
|