| № | Номер | Название | Опции | Альт |
|---|
| 1 | REF | INSTRUCTION | FRAME - backhoe mounting, see Fig. 68 for bushings | | | 2 | G103773 | CYLINDER | - backhoe swing, see parts list Fig. 42 | | | 3 | D120214 | BRACKET | SUPPORT - swing cylinders, welded assembly, replaces cast support on some machines, Includes: Ref.#4 | | | 4 | D60159 | BUSHING,60.55mm ID x 69.85mm OD x 38.1mm L | - plate | | | 5 | 13-1648 | BOLT,Hex, 1" - 8 x 3", Gr 5 | - hex head, 1" - 8 NC x 3" | | | 6 | 113-945 | BOLT,Hex, 1" - 8 x 5-1/2", Gr 5 | - hex head, special, 1" - 8 NC x 5-1/2" | | | 7 | D36505 | WASHER,26.99mm ID x 47.63mm OD x 2.38mm Thk | - heat treated, 1" | | | 8 | D86894 | PLATE | - tapped, if used | | | 8a | D94229 | LARGE PLATE | RETAINER - nut, if used | | | 8b | 129-568 | NUT,Sq, 1"-8, G5 | - square, 1" - 8 NC, if used, may be used to replace hex nuts | | | 9 | D90057 | COVER | - vinyl, bolt | | | 10 | D90868 | LATHE | SWING TOWER - see Fig. 72 for boom attaching parts, Includes: Ref.#11 - 13A | | | | When ordering a new swing tower, two D88985 pins (Ref. no. 14) and one D94031 plate (ref. no. 16) must also be ordered, unless these items are already installed. | | | | 11 | D49429 | BUSHING | - at boom cylinder | | | 12 | D91241 | BUSHING,51.02mm ID x 69.88mm OD x 60mm L | - boom mounting | | | 13 | D94018 | BUSHING,44.58mm ID x 53.98mm OD x 30mm L | - swing cylinder mounting, if used | | | 13a | D90863 | WASHER,58.35mm ID x 130mm OD x 6mm Thk | Washer - Bearing, welded to bottom of some swing towers, not used when Ref.# 22 is used 6mm Thk | | | 14 | D88985 | PIN,44.45mm OD x 181.5mm L | - swing cylinder to swing tower, 7-1/8" (181 mm) long, if used | | | 15 | D94019 | PIN,44.4mm OD x 196.5mm L | - swing cylinder to swing tower, 7-3/4" (197 mm) long, if used | | | 16 | D94031 | PLATE | - pin retaining, 6-3/8" (162 mm) long-mounts between pins, if used | | | 17 | D94189 | PLATE | - pin retaining, 11-3/8" (290 mm) long-mounts between pins, if used | | | 18 | 13-816 | BOLT,Hex, 1/2" - 13 x 1", Gr 5, Full Thd | | | | 19 | 92-8 | LOCK WASHER,1/2" | | | | 20 | D64050 | WASHER | - flat, 1/2" | | | 21 | D120495 | PIN | - tapered, swing tower to backhoe frame, lower | | | 22 | D89338 | SPACER | - bearing, if used, not used when Ref.#13A is used | | | 23 | 219-1 | LUBE NIPPLE,1/8" - 27 NPTF | GREASE FITTING - straight, 1/8" NPT | | | 25 | D120610 | NUT | - hex, 1-1/2" - 12 NF | | | 26 | D90576 | PIN | - lock, backhoe swing | | | 27 | D33805 | PIN | - self-locking | | | 28 | D90727 | PIN,57.15mm OD x 198mm L | - swing tower to backhoe frame, upper | | | 29 | 13-840 | BOLT,Hex, 1/2" - 13 x 2-1/2", Gr 5 | - hex head, 1/2" - 13 NC x 2-1/2" | | | 30 | 195-33 | WASHER,1/2" | - flat, 1/2" | | | 31 | 131-10 | NUT,1/2"-13, GB | NUT, LOCK, 1/2"-13, GB | | | 32 | D74249 | WASHER,60mm ID x 120mm OD x 2mm Thk | SPACER - bearing, 5/64" (2 mm) thick, if used | |
|
|