CASE > LIGHT EQUIPMENT > LOADER BACKHOES > K > (580K) - LOADER BACKHOE (NORTH AMERICA) (1/87-12/94) > (09) - CHASSIS/ATTACHMENTS > (09-532) - THREE-POINT HITCH FRAME, DRAFT ARMS, LINKAGE, AND CYLINDER MOUNTING

№ Номер Название Опции Альт 1 D141042 FRAME ASSY SUPPORT three-point hitch frame 2 26-1248 BOLT,Hex, 3/4" - 10 x 3", Gr 8 - hex, 3/4" -10 NC x 3, G8 3 D34666 WASHER,33.34mm ID x 63.5mm OD x 2.38mm Thk flat, 3/4", hardened 4 129-138 NUT,3/4"-10, G8 5 D141091 FRAME ASSY FRAME three-point hitch 6 D141094 SHIM,1.6mm Thk (1/16") 1.6mm Thk 7 D141095 SHIM,3mm Thk (1/8") 3mm Thk 8 113-977 BOLT,Hex, 1-1/4" - 7 x 3-1/2", Gr 5 8a D64968 WASHER flat, 1-1/4", hardened 9 25-1020 NUT,1 1/4"-7, G5 10 D133267 PIN hitch, Serial Range: frame-support 11 D33805 PIN lock 12 D72875 TUBE,23.6" L rockshaft, Includes: Ref. 13 13 D50146 BUSHING,44.68mm ID x 57.15mm OD x 38.1mm L tube 14 219-1 LUBE NIPPLE,1/8" - 27 NPTF GREASE FITTING straight, 1/8" NPT 15 D51569 SHAFT ROCKSHAFT three-point hitch 16 113-241 BOLT,Hex, 3/8" - 16 x 3", Gr 5 17 192-21 LOCK WASHER,3/8" WASHER, LOCK, 3/8" 18 129-103 NUT,Hex, 3/8" - 16, Gr 5 NUT, 3/8"-16, G5 19 G101189 CYLINDER ASSY. CYLINDER ASSEMBLY lift, see Figure 08-434 20 D51302 PIN mounting, lift cylinder, upper 21 D26918 SNAP RING,#125, Ext Ring, Snap, , pin #125, Ext 22 D51692 SPACER lift cylinder mounting pin, lower 23 D51695 PIN mounting, lift cylinder, lower 24 113-257 BOLT,Hex, 3/8" - 16 x 2-1/2", Gr 5 25 192-21 LOCK WASHER,3/8" WASHER, LOCK, 3/8" 26 129-103 NUT,Hex, 3/8" - 16, Gr 5 NUT, 3/8"-16, G5 27 1976884C1 JACK BODY CYLINDER ASSEMBLY pitch, see Figure 08-438 138235A1R REMAN-HYD CYLINDER 580K, Reman For New P/N 1976884C1 138235A1C CORE-HYD CYLINDER Return Number 28 D141090 PIN mounting, pitch cylinder at mounting frame 29 D25277 SNAP RING,23.5mm ID x 2.62mm Thk pin retaining 30 D140990 PIN 1" diameter, pitch cylinder to equipment, for use with category II hitch, if used, Includes: Ref. 31 31 138-140 LOCK PIN,1/4" x 1 3/4", Slotted PIN, 1/4" x 1 3/4", Slotted 32 D33805 PIN lock 33 D141292 PIN 3/4" diameter, pitch cylinder to equipment, for use with category I hitch, if used 34 D141156 TUBE BUSHING pivot, pitch cylinder rod eye, used with D141292 pin to adapt for use with category I hitch, if used 35 D51299 PIN mounting, tilt cylinder and strut, upper 36 D25277 SNAP RING,23.5mm ID x 2.62mm Thk pin retaining 37 D51276 STAND STRUT stationary 38 D51297 PIN mounting, strut, lower 39 D25277 SNAP RING,23.5mm ID x 2.62mm Thk pin retaining 40 G101188 JACK BODY CYLINDER ASSEMBLY tilt, see Figure 08-436 41 D30609 PIN,25.4mm OD x 95.25mm L mounting, tilt cylinder, lower 42 195-553 WASHER,1", SAE flat, 1", plated, cylinder alignment 43 D25277 SNAP RING,23.5mm ID x 2.62mm Thk pin retaining 44 D141088 ARM draft, left hand 45 D141087 ARM draft, right hand, Includes: Ref. 46-48 46 D51608 BUSHING,25.63mm ID x 34.92mm OD x 25.4mm L arm, 1", 25 mm ID 47 H363424 BALL JOINT BUSHING - self-aligning, 1-1/8" pin size 48 D51609 BALL JOINT BUSHING self-aligning, 1" pin size 49 D141104 TUBE BUSHING pivot, draft arm mounting pin 50 D50724 PIN,25.4mm OD x 160.27mm L mounting, draft arm to mounting frame 51 113-257 BOLT,Hex, 3/8" - 16 x 2-1/2", Gr 5 52 192-21 LOCK WASHER,3/8" WASHER, LOCK, 3/8" 53 129-103 NUT,Hex, 3/8" - 16, Gr 5 NUT, 3/8"-16, G5 54 D140991 BUSHING,22.48mm ID x 28.57mm OD x 44.45mm L draft arm to equipment, for use with category I hitch, if used 55 D141085 CASTING RETAINER sway, draft arm 56 113-412 BOLT,Hex, 1/2" - 13 x 1-3/4", Gr 5 57 195-533 WASHER,1/2", SAE flat, 1/2", plated 58 131-70 NUT,1/2"-13, GB NUT hex, self-locking, 1/2" - 13 NC, plated