| № | Номер | Название | Опции | Альт |
|---|
| 1 | D135552 | FRAME ASSY | FRAME backhoe mounting, for use on loader models with demountable backhoe only, no longer available, Includes: Ref. 2 thru 5B | | | | For service order P/N D144455 frame shown below, and P/N 413-8112 bolt, P/N D73296 washer, P/N 492-11050 washer, and P/N 425-108 nut in Figure 09-478 | | | | 1a | D144455 | FRAME | backhoe mounting, for use on loader models with demountable backhoe only, Includes: Ref. 2 thru 5B | | | 2 | D135555 | BUSHING,70.19mm ID x 90mm OD x 32mm L | upper, backhoe frame, swing tower mounting | | | 3 | D135556 | BUSHING,70.19mm ID x 90mm OD x 38mm L | lower, backhoe frame, swing tower mounting | | | 4 | D136472 | SPACER | 3-1/4" (83 mm) ID x 5-5/16" (135 mm) OD x 1/4" (6 mm) thick, bearing, Serial Range: welds-frame | | | 5 | D43940 | BUSHING,44.68mm ID x 57.15mm OD x 25.4mm L | lower, side, backhoe frame, at stabilizer leg mounting | | | 5a | D143460 | LARGE PLATE | PLATE gusset, used with P/N D136740 gusset, also order P/N 8-75630 instruction sheet | | | 5b | D136740 | GUSSET | frame, used with P/N D143460 plate, also order P/N 8-75630 instruction sheet | | | 6 | 26-1248 | BOLT,Hex, 3/4" - 10 x 3", Gr 8 | - hex, 3/4" -10 NC x 3, G8, used with Ref 1 demountable backhoe frame only | | | 7 | D34666 | WASHER,33.34mm ID x 63.5mm OD x 2.38mm Thk | flat, 3/4", hardened, used with Ref. 1 demountable backhoe frame only | | | 8 | 129-572 | NUT,3/4"-10, G8 | Used with Ref. 1 demountable backhoe frame only 3/4"-10, G8 | | | 9 | D127974 | SEAL,67.46mm ID x 80.18mm OD x 3.56mm Thk | frame, at swing tower mounting | | | 10 | REF | INSTRUCTION | CYLINDER stabilizer, right hand, see Figure 08-414 | | | 11 | REF | INSTRUCTION | CYLINDER stabilizer, left hand, see Figure 08-414 | | | 12 | D133509 | PIN,38.1mm OD x 299mm L | stabilizer, Serial Range: cylinder-frame | | | 13 | D25279 | SNAP RING,M35, Int | RING snap, pin retaining | | | 14 | D133428 | STABILIZER | LEG stabilizer, Includes: Ref. 15 | | | 15 | D50146 | BUSHING,44.68mm ID x 57.15mm OD x 38.1mm L | leg to frame | | | 16 | D134723 | PIN | stabilizer, Serial Range: leg-frame | | | 17 | 195-2152 | WASHER,1 13/16" x 2 1/2" x .109" | flat, 1-3/4" bolt size, 1-13/16" ID x 2-1/2" OD x 1/8" thick | | | 18 | D25280 | SNAP RING,#175, Ext | Ring, Snap, , pin #175, Ext | | | 19 | D26002 | PIN,38.1mm OD x 187.32mm L | stabilizer, Serial Range: cylinder-leg | | | 20 | D25279 | SNAP RING,M35, Int | RING snap, pin retaining | | | 21 | D88427 | PLATE | stabilizer, cleated, if used | | | 22 | D28648 | PIN,1.5" OD x 10 7/16" L | P/N D88427 stabilizer, Serial Range: plate-leg | | | 23 | D31312 | WASHER | spacer, 2-3/4" (70 mm) OD x 1/16" (1.6 mm) thick, hardened | | | 24 | D28610 | WASHER,38.5mm ID x 63.5mm OD x 2.66mm Thk | spacer, 1-1/2" (38 mm) ID x 2-1/2" (64 mm) OD x 7/64" (3 mm) thick | | | 25 | D25279 | SNAP RING,M35, Int | RING snap, pin retaining | | | 26 | D61376 | STABILIZER | PLATE stabilizer, street or cemetery, uses P/N D61368 pad, no longer available, order P/N D142519 plate and P/N D39256 pin, see Ref. 37 and 38 in Figure 09-482 | | | 27 | D61368 | PAD | Rubber, used with P/N D61376 plate, if used | | | 28 | D50696 | PIN,38.1mm OD x 225.55mm L | 8-7/8" (226 mm) long, P/N D61376 stabilizer plate to leg, if used | | | 29 | 113-713 | BOLT,Hex, 3/4" - 10 x 1-3/4", Gr 5 | If used Hex, 3/4"-10 x 1 3/4", G5 | | | 30 | 129-108 | NUT,3/4"-10, G5 | If used 3/4"-10, G5 | |
|
|