| № | Номер | Название | Опции | Альт |
|---|
| 1 | R47701 | HALF BLADE | BLADE - with hose guards welded on back, no longer available, order R47698 blade (ref. 2), see figures 8-339 and 8-341 for the correct optional tilt hydraulic circuit used with this blade, Includes: Ref. 3 and 4 | | | | If you replace R47701 blade with R47698 blade, you must also replace hydraulic circuit components shown on Figures 8-338 and 8-340 with corresponding replacement components shown on Figures 8-342 and 8-344. Or, you may adapt R47698 blade to fit your present hydraulic circuit by making weldment adjustments to the back of the blade, compare Ref. 1 and 2 on this Figure | | | | 2 | R47698 | HALF BLADE | BLADE - with tapped blocks for tube mounting on back, see figures 8-343 and 8-345 for the correct optional tilt hydraulic circuit used with this blade, Includes: Ref. 3 and 4 | | | | The dowel pin P/N R37120, NSS, is part of R47698 Blade weldment | | | | 3 | R37089 | BRACKET | - strut mounting, R47701 and R47698 blades | | | 4 | R37331 | PIN | - bracket, R47701 and R47698 blades | | | 5 | R41908 | EDGE, CUTTING | CUTTING EDGE - center | | | 6 | R41909 | EDGE, CUTTING | CUTTING EDGE - intermediate | | | 7 | R42490 | END | CUTTING EDGE - end, flat type | | | 8 | R41910 | EDGE, CUTTING | CUTTING EDGE - left-hand, curved type, heavy duty | | | 9 | R41911 | EDGE, CUTTING | CUTTING EDGE - right-hand, curved type, heavy duty | | | 10 | R56474 | PLOW BOLT | - dome head, 3/4" - 10 NC x 2-1/2", grade 8 | | | 11 | 192-27 | LOCK WASHER,3/4" | WASHER, LOCK, 3/4" | | | 12 | 129-572 | NUT,3/4"-10, G8 | | | | 13 | R47093 | BRACKET | - blade pivot | | | 14 | 13-1648 | BOLT,Hex, 1" - 8 x 3", Gr 5 | - hex head, 1" - 8 NC x 3" | | | 15 | D30196 | WASHER | - hardened, 1/4" (6 mm) thick | | | 16 | R42967 | PIVOT PIN | PIN - pivot bracket | | | 17 | 132-157 | COTTER PIN,Ext Prong Sq Cut, 1/4" x 2 1/2" | Pin, Split (Cotter), 1/4" x 2 1/2" | | | 18 | R26660 | WASHER,40.39mm ID x 101.6mm OD x 12mm Thk | - special, pin | | | 19 | 25-1224 | SLOTTED NUT,1 1/2"-6, G5 | CASTLE NUT - 1-1/2" - 6 NC | | | 20 | R46832 | HITCH PIN | PIN - lower, Serial Range: strut-C-frame | | | 21 | R42993 | PIN | - tee, strut mounting | | | 22 | 136-163 | HAIR PIN COTTER,Int, 5/16" x .177 | HAIR PIN - tee pin | | | 23 | R42965 | PIN | - lower strut, rear | | | 24 | D26919 | SNAP RING,#200, Ext | Ring, Snap, , pin #200, Ext | | | 25 | R46580 | FRAME | STRUT - lower, left-hand, with self-aligning bushing, replaces strut without bushing on some models | | | 26 | R46579 | FRAME | STRUT - lower, right-hand, with self-aligning bushing, replaces strut without bushing on some models, Includes: Ref. 26A and 26B | | | 26a | L74160 | BEARING | BUSHING - self-aligning, R46580 and R46579 struts | | | 26b | A10506 | SNAP RING,2.44", Int, #244 | Ring, Snap, , bushing, R46580 and R46579 struts 2.44", Int, #244 | | | 27 | R42880 | JACK HEAD | CLEVIS - lower strut | | | 28 | D42787 | PIN | - clevis to blade, lower strut, requires two snap rings per pin, no longer used, order ref. 28A | | | 28a | R48243 | PIN | - clevis to blade, lower strut, requires one snap ring per pin | | | 29 | D25279 | SNAP RING,M35, Int | - pin | | | 30 | R37207 | PIN | - upper, Serial Range: strut-C-frame | | | R42884 | STRUT | ASSEMBLY - upper, Includes: Ref. 31 - 34 | | | 31 | R42883 | STRUT | - upper | | | 32 | R42877 | JACK HEAD | CLEVIS - rear | | | 33 | R42879 | JACK HEAD | CLEVIS - front | | | 34 | 219-1 | LUBE NIPPLE,1/8" - 27 NPTF | GREASE FITTING - straight, 1/8" NPT | | | 35 | R43491 | HANDLE | - strut locking and adjusting | | | 36 | 136-163 | HAIR PIN COTTER,Int, 5/16" x .177 | HAIR PIN - strut handle | | | 37 | D42787 | PIN | - upper, Serial Range: strut-blade | |
|
|