| № | Номер | Название | Опции | Альт |
|---|
| 1 | D136588 | CHASSIS | ASSEMBLY - includes upper frame, used on models with 24 volt electrical cirucit, also includes Refs. 16-29 in Figure 3-60, Includes: Ref. 2 - 22 | | | 1a | D138640 | CHASSIS | SPARE PART ASSEMBLY - includes upper frame, not shown, used on models with 12 volt electrical circuit, also includes Refs. 16-29 in Figure 3-60 | | | 2 | L11494 | BUSHING | front axle pivot | | | 3 | L105212 | BUSHING,57.35mm ID x 69.98mm OD x 46mm L | loader lift frame pivot | | | 4 | L105212 | BUSHING,57.35mm ID x 69.98mm OD x 46mm L | lift cylinder pivot | | | 5 | D60159 | BUSHING,60.55mm ID x 69.85mm OD x 38.1mm L | swing cylinder pivot, lower | | | 6 | D33024 | BUSHING,51.02mm ID x 63.5mm OD x 25.4mm L | stabilizer, Serial Range: leg-frame | | | 7 | D34340 | BUSHING,44.68mm ID x 53.98mm OD x 25.4mm L | stabilizer, Serial Range: cylinder-frame | | | 9 | L102293 | BUSHING | upper, swing tower mounting | | | 10 | L102294 | BUSHING | lower, swing tower mounting | | | 11 | L101688 | SHAFT | lift cylinder mounting | | | 12 | L100349 | PLUG | CAP - filler, hydraulic reservoir | | | 13 | A7552 | O-RING,0.21" Thk x 1.975" ID, -329, Cl 5, 75 Duro | filler cap | | | 15 | 113-695 | BOLT,Hex, 1/2" - 13 x 4", Gr 5 | hex head, 1/2" - 13 NC x 4", special thread length | | | 16 | L78045 | WASHER | special | | | 17 | A27410 | O-RING,0.487" ID x 0.693" OD x 0.103" | cover | | | 18 | L77124 | COVER ASSY | access, hydraulic filter | | | 19 | L55410 | O-RING,0.275" Thk x 7.22" ID, -442, Cl 5, 75 Duro | cover, hydraulic reservoir | | | 20 | L50741 | BAR | cover retainer | | | 21 | 131-510 | LOCK NUT,1/2"-13 | | | | 22 | 221-677 | DRAIN PLUG,Sq Hd, 3/4" NPT | square head, 3/4" NPT, magnetic, reservoir drain | | | 23 | D128526 | FILTER CARTRIDGE | SCREEN - suction | | | 23a | 113-207 | BOLT,Hex, 3/8" - 16 x 1", Gr 5 | Not shown, located on RH frame to mount ground wires, use on models with D138640 chassis only | | | 24 | 195-104 | WASHER,3/8" | flat, , plated, not shown, located on right-hand frame to mount ground wires, use on models with D138640 chassis only 3/8" | | | 24a | 192-21 | LOCK WASHER,3/8" | Not shown, located on RH frame to mount ground wires, use on models with D138640 chassis only | | | 25 | 219-36 | LUBE NIPPLE,45 Degree Elbow, 1/8" - 27 NPTF | Special short | | | 26 | 219-87 | LUBE NIPPLE,1/4" - 28 NPTF | | | | 26a | 219-1 | LUBE NIPPLE,1/8" - 27 NPTF | | | | 27 | D133561 | COVER ASSY | front | | | 28 | 113-410 | BOLT,Hex, 1/2" - 13 x 1-1/2", Gr 5, Full Thd | | | | 29 | 192-23 | LOCK WASHER,1/2" | | | | 30 | 195-106 | WASHER,1/2" | flat, plated | | | 31 | L102993 | STEP | SPARE PART upper | | | 32 | L102994 | STEP | lower | | | 33 | 113-421 | BOLT,Hex, 1/2" - 13 x 2", Gr 5 | | | | 34 | 129-105 | NUT,Hex, 1/2" - 13, Gr 5 | | | | L79110 | GAUGE | ASSEMBLY - hydrualic oil level, Includes: Ref. 35 - 42 | | | 35 | NSS | NOT SOLD SEPARAT | BODY - gauge, includes end plugs | | | 36 | N8537 | O-RING,0.103" Thk x 0.487" ID, -112, Cl 7, 75 Duro | gauge | | | 37 | 92-8 | LOCK WASHER,1/2" | | | | 38 | 131-402 | NUT,PAL, 1/2"-20 | hex, special locking, 1/2" - 20 NF | | | 39 | D75821 | STUD | mounting | | | 40 | N8539 | O-RING,0.07" Thk x 0.364" ID, -12, Cl 5, 75 Duro | end plugs to body | | | 41 | D75820 | TUBE | sight, internal | | | 42 | D75819 | GASKET | internal, sight tube | | | 43 | 221-727 | PIPE,Nipple, 1/4" NPT x 18" | 1/4" NPT x 18" | | | 44 | D93753 | PADLOCK | includes keys, Includes: Ref. 45 and 46 | | | 45 | R29555 | KEY | for Master padlock only | | | 46 | D93751 | SET OF 2 KEYS | for Yale padlock only | | | D102830 | KIT | rear axle reinforcement, includes instruction sheet, Includes: Ref. 47 - 50 | | | 47 | NSS | NOT SOLD SEPARAT | GUSSET - rear | | | 48 | NSS | NOT SOLD SEPARAT | PLATE - reinforcement | | | 49 | NSS | NOT SOLD SEPARAT | PLATE - axle, right-hand | | | 50 | NSS | NOT SOLD SEPARAT | PLATE - axle, left-hand, not shown | |
|
|