| № | Номер | Название | Опции | Альт |
|---|
| R47241 | BUCKET ASSEMBLY - clam, with corner teeth, replaces bucket without corner teeth, uses 3/4" dia. hardware for tooth mounting, no longer available, order R53285 clam bucket and correct teeth on Fig. 9-448, Includes: Ref. 1 - 28 | | | | R53285 | BUCKET ASSEMBLY - clam, with corner teeth, uses 1" dia. hardware for tooth mounting, Includes: Ref. 1 - 28 | | | | 1 | R47240 | BUCKET | CLAM ASSEMBLY - bucket, with corner teeth, uses 3/4" dia. hardware for tooth mounting, no longer available, order R53399 clam assembly and correct teeth on Fig. 9-448, Includes: Ref. 2 - 4 | | | 1 | R53399 | ASSEMBLY | CLAM ASSEMBLY - bucket, with corner teeth, uses 1" dia. hardware for tooth mounting, Includes: Ref. 2 - 4 | | | 2 | R28276 | BLADE | CUTTING EDGE - clam, without corner teeth, if used | | | 2a | R46009 | EDGE, CUTTING | CUTTING EDGE - clam, with corner teeth, uses 3/4" dia. hardware for tooth mounting, no longer available, order R51169 cutting edge | | | 2a | R51169 | EDGE, CUTTING | CUTTING EDGE - clam, with corner teeth, uses 1" dia. hardware for tooth mounting, if used | | | 3 | D51545 | BUSHING,63.75mm ID x 76.2mm OD x 38.1mm L | - clam pivot | | | 4 | D37392 | BUSHING,44.68mm ID x 53.98mm OD x 31.75mm L | - cylinder pivot | | | 5 | R53410 | BLADE | ASSEMBLY - bucket, Includes: Ref. 6 and 7 | | | 6 | D53823 | BUSHING | - upper | | | 7 | R28235 | BUSHING | - lower | | | 8 | D50492 | BLADE | CUTTING EDGE - blade, ends | | | 9 | R28754 | BLADE | CUTTING EDGE - blade, center | | | 10 | R56474 | PLOW BOLT | - dome head, 3/4" - 10 NC x 2-1/2", plated | | | 11 | 192-27 | LOCK WASHER,3/4" | WASHER, LOCK, 3/4" | | | 12 | 129-108 | NUT,3/4"-10, G5 | | | | 13 | 21-55 | GREASE FITTING - 90 degree, 1/8" NPT | | | | 14 | D50491 | PIN | - pivot, blade | | | 15 | 113-259 | BOLT,Hex, 3/8" - 16 x 4-1/2", Gr 5 | | | | 16 | 131-178 | LOCK NUT,Prev Torque, Hex, 3/8" - 16, Gr A | NUT - hex, self-locking, 3/8" - 16 NC, plated | | | 17 | D38481 | PIN | - clam cylinder, rod end | | | 18 | 95-28 | WASHER,1 7/8" x 4" x .179" | - flat, 1-7/8" (48 mm) ID | | | 19 | D25280 | SNAP RING,#175, Ext | Ring, Snap, , cylinder pin #175, Ext | | | 20 | D50490 | PIN | - clam cylinder, closed end | | | 21 | 113-267 | BOLT,Hex, 3/8" - 16 x 4", Gr 5 | | | | 22 | 131-178 | LOCK NUT,Prev Torque, Hex, 3/8" - 16, Gr A | NUT - hex, self-locking, 3/8" - 16 NC, plated | | | 23 | R29976 | GUARD | - cylinder, right-hand | | | 24 | R29975 | GUARD | - cylinder, left-hand | | | 25 | 113-410 | BOLT,Hex, 1/2" - 13 x 1-1/2", Gr 5, Full Thd | | | | 26 | 192-23 | LOCK WASHER,1/2" | WASHER, LOCK, 1/2" | | | 27 | 195-533 | WASHER,1/2", SAE | - flat, 1/2", plated | | | 28 | 321-1706 | DECAL | - indicator, clam bucket position | |
|
|