| № | Номер | Название | Опции | Альт |
|---|
| 1 | D50134 | LATHE | TOWER - swing, Includes: Ref. 2 | | | 2 | D49429 | BUSHING | - at boom cylinder, closed end | | | 3 | 13-814 | BOLT,Hex, 1/2" - 13 x 7/8", Gr 5, Full Thd | Hex 1/2"-13 x 7/8", G5, Full Thd, if D50148 spacer is used | | | 3 | 13-812 | BOLT,Hex, 1/2" - 13 x 3/4", Gr 5 | - hex, 1/2" - 13 NC x 3/4", if D50148 spacer is not used | | | 4 | 92-8 | LOCK WASHER,1/2" | | | | 5 | D50149 | BLOCK | - pin locking | | | 6 | D50148 | BUSHING | SPACER - locking block, if used | | | 7 | D50700 | PIN | - boom to swing tower | | | 8 | 219-1 | LUBE NIPPLE,1/8" - 27 NPTF | GREASE FITTING - straight, 1/8" NPT | | | 9 | D54944 | | BOOM - backhoe, Includes: Ref. 10 - 13 | | | 10 | D50698 | BUSHING,51.03mm ID x 69.98mm OD x 40.64mm L | - boom pivot | | | 11 | D95362 | BUSHING | - boom cylinder anchor | | | 12 | D31142 | BUSHING,51.02mm ID x 63.5mm OD x 38.1mm L | - dipper pivot | | | 13 | D37416 | BUSHING | SPACER - bushing | | | 13a | D44813 | SHIM,53.34mm ID x 76.2mm OD x 0.89mm Thk | Spacer, between swing tower and boom .035" Thk | | | 14 | D54934 | SHAFT | - pivot, boom lock, before backhoe, use D55996, Serial Range: -5220178 | | | 14 | D55996 | SHAFT | - pivot, boom lock, backhoe, Start Serial: 5220178 | | | 15 | D54947 | SNAP RING,#131, Ext | Ring, Snap, , pin, used with D54934 shaft #131, Ext | | | 15 | D56051 | SNAP RING,#137. Ext | Ring, Snap, #137, Ext, pin, used with D55996 shaft | | | 15a | 195-2131 | WASHER,1 3/8" x 2" x .065" | - plain, 1-3/8" ID x 2" OD, used with D54934 shaft | | | 15a | 195-2140 | WASHER,1 7/16" x 2" x .065" | - plain, 1-7/16" ID x 2" OD, used with D55996 shaft | | | 15b | D55073 | LEVER | AND LATCH - transport lock, used with D54934 shaft on backhoes before, for service, order, 1, D58285 lever and latch, 1, D55996 shaft, 2, D56051 retaining rings, and 6, 195-2140 washers, Serial Range: -5220178 | | | 15b | *D58285 | LEVER AND LATCH - transport lock, backhoe, Start Serial: 52201786 | | | | 15c | D63988 | SPRING | - transport latch | | | 16 | D49866 | PIN,38.1mm OD x 96.52mm L | - boom, Serial Range: cylinder-tower | | | 16a | 219-1 | LUBE NIPPLE,1/8" - 27 NPTF | GREASE FITTING - straight, 1/8" NPT | | | 17 | 13-656 | BOLT,Hex, 3/8" - 16 x 3-1/2", Gr 5 | - hex, 3/8" - 16 NC x 3-1/2" | | | 18 | 131-352 | LOCK NUT,3/8"-16, GA | NUT - hex, lock, 3/8" - 16 NC | | | 19 | D28610 | WASHER,38.5mm ID x 63.5mm OD x 2.66mm Thk | - special, if used | | | 20 | REF | INSTRUCTION | CYLINDER - hydraulic, boom, see Figures 292 - 298 | | | 21 | G32079 | CYLINDER | - hydraulic, dipper, parts list Figures 300 - 304 | | | 22 | 13-864 | BOLT,Hex, 1/2" - 13 x 4", Gr 5 | - hex, 3/8" - 16 NC x 4" | | | 23 | D49865 | PIN,50.8mm OD x 304.8mm L | - boom, Serial Range: cylinder-boom | | | 24 | 131-354 | LOCK NUT,1/2"-13, GA | NUT - hex, lock, 1/2" - 13 NC | | | 25 | 195-2155 | WASHER,2 1/16" x 3" x .109" | - flat, 2" ID | | | 26 | 219-1 | LUBE NIPPLE,1/8" - 27 NPTF | GREASE FITTING - straight, 1/8" NPT | | | 27 | 195-2155 | WASHER,2 1/16" x 3" x .109" | - flat, 2" ID | | | 28 | D72359 | PIN,44.45mm OD x 142.24mm L | - dipper, Serial Range: cylinder-boom | | | 29 | D25280 | SNAP RING,#175, Ext | Ring, Snap, , pin #175, Ext | | | 30 | D52522 | PIN,44.45mm OD x 211.84mm L | - dipper, Serial Range: cylinder-dipper | | | 31 | D25280 | SNAP RING,#175, Ext | Ring, Snap, , pin #175, Ext | | | 32 | 195-2152 | WASHER,1 13/16" x 2 1/2" x .109" | - flat, 1-3/4" ID | | | 33 | D26919 | SNAP RING,#200, Ext | Ring, Snap, , pin #200, Ext | | | 34 | 195-2155 | WASHER,2 1/16" x 3" x .109" | - flat, 2" ID | | | 35 | D45523 | PIN,50.8mm OD x 276.35mm L | -, Serial Range: boom-dipper | | | 36 | 219-55 | LUBE NIPPLE,90 Degree Elbow, 1/8" - 27 NPTF | NIPPLE, LUBE, 90º, 1/8" NPT x .84" lg | | | 37 | D25280 | SNAP RING,#175, Ext | Ring, Snap, , pin #175, Ext | | | 38 | 195-2152 | WASHER,1 13/16" x 2 1/2" x .109" | - flat, 1-3/4" ID | | | 39 | D52522 | PIN,44.45mm OD x 211.84mm L | - dipper to bucket cylinder | | | 40 | D49858 | ARM | DIPPER ARM - backhoe, when stock is exhausted,order D56528 dipper arm for service, Includes: Ref. 41 - 45 | | | 40 | D56528 | DIPPER | ARM - backhoe, when stock is exhausted,order D63796 dipper arm for service, Includes: Ref. 41 - 45 | | | 40 | D63796 | ARM | DIPPER ARM - backhoe, Includes: Ref. 41 - 45 | | | 41 | D52434 | BUSHING | - dipper, at dipper cylinder | | | 42 | D43946 | BUSHING,51.02mm ID x 63.5mm OD x 35.6mm L | - dipper, at boom, 1-13/32" long | | | 42 | D31142 | BUSHING,51.02mm ID x 63.5mm OD x 38.1mm L | - dipper, at boom, 1-1/2" long | | | 43 | D33094 | BUSHING | - dipper, at bucket cylinder, 2-1/2" long | | | 43 | D40089 | BUSHING | - dipper, at bucket cylinder, 2" long | | | 43 | D34340 | BUSHING,44.68mm ID x 53.98mm OD x 25.4mm L | - dipper at bucket cylinder, 1" long | | | 44 | 50146 | NUT | BUSHING - dipper, at bucket links | | | 45 | D55626 | BUSHING,44.68mm ID x 57.15mm OD x 41.91mm L | - dipper, at bucket | | | 46 | REF | INSTRUCTION | CYLINDER - hydraulic, bucket, see Figures 306 - 312 | | | 47 | D25280 | SNAP RING,#175, Ext | Ring, Snap, , pin #175, Ext | | | 48 | 195-2152 | WASHER,1 13/16" x 2 1/2" x .109" | - flat, 1-/4" ID | | | 49 | D53818 | PIN,44.45mm OD x 278.89mm L | - bucket linkage to dipper arm | | | 50 | 55732 | WASHER - special | | | | 51 | D53839 | LINK | - bucket cylinder to dipper arm, LH, when stock is exhausted, order RH and LH links, D61087 and D61088 for service | | | 51 | D61088 | LINK | - bucket cylinder to dipper arm, LH | | | 52 | D53840 | LINK | - bucket cylinder to dipper arm, RH, when stock is exhausted, order RH and LH links, D61087 and D61088 for serivce, Includes: Ref. 53 and 54 | | | 52 | D61087 | LINK | - bucket cylinder to dipper arm, RH, Includes: Ref. 53 and 54 | | | 53 | D46405 | BUSHING,44.68mm ID x 53.98mm OD x 19.05mm L | - link, at dipper arm | | | 54 | D42788 | BUSHING,44.68mm ID x 53.98mm OD x 28.57mm L | - link, at bucket cylinder | | | 55 | D50157 | LINK | - bucket cylinder to bucket, when stock is exhausted, order D61244 link for service, Includes: Ref. 56 and 57 | | | 55a | D61244 | LINK | - bucket cylinder to bucket, Includes: Ref. 56 and 57 | | | 56 | D37495 | BUSHING,44.76mm ID x 57.15mm OD x 31.75mm L | - link, at bucket cylinder | | | 57 | D30933 | BUSHING,38.41mm ID x 47.63mm OD x 31.75mm L | - link at bucket | | | 58 | 195-2152 | WASHER,1 13/16" x 2 1/2" x .109" | - flat, 1-3/4" ID | | | 59 | D25279 | SNAP RING,M35, Int | RING - retaining | | | 60 | D28610 | WASHER,38.5mm ID x 63.5mm OD x 2.66mm Thk | - special | | | 61 | D30899 | PIVOT PIN,38.1mm OD x 338.14mm L | PIN - link to bucket, used on shovel and ditching buckets only | | | 61 | D37614 | PIN,38mm Od x 246mm L | - link to bucket, used on all buckets except shovel and ditching buckets | | | 62 | D37793 | PIN | - link to frost point, 1-1/2" OD x 14-9/16" long, H and L frost point | | | 62 | D54218 | PIN,38.1mm OD x 345.95mm L | - link to frost point, 1-1/2" OD x 13-5/8" long, Case manufactured frost point | | | 62a | 195-63 | WASHER,1 5/8" x 3 1/4" x .180" | - plain, 1-9/16" ID, used with D54218 pin only | | | 63 | D37450 | SPACER,40.89mm ID x 48.26mm OD x 63.5mm L | SPACER - link | | | 64 | 219-1 | LUBE NIPPLE,1/8" - 27 NPTF | GREASE FITTING - straight, 1/8" NPT | | | 65 | D25280 | SNAP RING,#175, Ext | Ring, Snap, #175, Ext | | | 66 | 195-2152 | WASHER,1 13/16" x 2 1/2" x .109" | - flat, 1-3/4" ID | | | 67 | D64799 | PIN,44.45mm OD x 370.84mm L | - dipper arm to bucket, all buckets except 12" buckets | | | 68 | D55584 | PIN,44.45mm OD x 327.15mm L | - dipper arm to bucket, lubricated, 12" buckets only | | | 69 | 219-1 | LUBE NIPPLE,1/8" - 27 NPTF | GREASE FITTING - straight, 1/8" NPT | | | 70 | D25280 | SNAP RING,#175, Ext | Ring, Snap, , pin #175, Ext | | | 71 | REF | INSTRUCTION | BUCKET - backhoe, see Figures 388 - 394 | | | D42577 | SPARE PART | FROST POINT ASSEMBLY - backhoe, H and L manufactured, Includes: Ref. 72 - 74 | | | 72 | NSS | NOT SOLD SEPARAT | BODY - frost point | | | 73 | D83306 | POINT | - tooth | | | 74 | D43417 | PIN | FLEX PIN - point | | | 75 | D54136 | SUPPORT ASSY. | BODY - frost point, Case manufactured, Includes: Ref. 76 | | | 76 | D37495 | BUSHING,44.76mm ID x 57.15mm OD x 31.75mm L | - frost point pivot | | | 77 | 83306 | POINT - tooth | | | | 78 | D43417 | PIN | FLEX PIN - point | | | 79 | D55082 | LOCK PIN,38.1mm OD x 208.53mm L | PIN - lock, boom transport | | | 80 | D28610 | WASHER,38.5mm ID x 63.5mm OD x 2.66mm Thk | - plain, 1-1/2" ID,.105" thick | | | 81 | D31312 | WASHER | - plain, 1-1/2" ID,.062" thick | | | 82 | D25279 | SNAP RING,M35, Int | RING - retaining, pin | | | 83 | 195-2152 | WASHER,1 13/16" x 2 1/2" x .109" | - flat, 1-3/4" | | | 84 | D62468 | GUARD | - boom cylinder | | | 85 | D62467 | BRACKET | - guard mounting | | | 86 | 13-548 | CAP,Hex, 5/16" - 18 x 3", Gr 5 | BOLT - hex, 5/16" - 18 NC x 3" | | | 87 | 131-4 | LOCK NUT,5/16"-18, GB | NUT - hex, lock, 5/16" - 18 NC | |
|
|