| № | Номер | Название | Опции | Альт |
|---|
| 1 | REF | INSTRUCTION | VALVE ASSEMBLY backhoe control, for correct assembly and components, see Figure 8-080 or 8-082 | | | 2 | 413-624 | BOLT,Hex, 3/8" - 16 x 1-1/2", Gr 5 | hex, 3/8 NC x 1-1/2 inch | | | 3 | 492-11038 | LOCK WASHER,3/8" | | | | 4 | D52275 | WASHER,9.92mm ID x 31.75mm OD x 2.78mm Thk | flat, 25/64 x 1-1/4 x 7/64 inch, hardened | | | 5 | D52276 | ISOLATOR,10.16mm ID x 28.07mm OD x mm L | INSULATOR rubber | | | 6 | 495-81266 | WASHER,0.41" ID x 0.88" OD x 0.07" Thk | flat, 13/32" ID x 7/8" OD x 1/16" thick, if used | | | 7 | 413-828 | BOLT,Hex, 1/2" - 13 x 1-3/4", Gr 5 | | | | 8 | 80679 | LOCK WASHER,1/20.507 CST ZND | WASHER, LOCK, 1/2" | | | 9 | 425-108 | NUT,1/2" - 13, Gr 5 | NUT, , Hex 1/2"-13, G5 | | | 10 | 218-5107 | 90 ELBOW,90 Degree Elbow, 7/8" - 14 Male JIC x 7/8" - 14 Male ORB | 90 degree, 7/8-14 inch flare x adj O-ring boss, Incl. Ref. 11 | | | 11 | 237-6010 | O-RING,0.097" Thk x 0.755" ID, -910, Cl 6, 90 Duro | 10-1, 90 Duro, .755" ID x .097" Thk | | | 12 | D145473 | HOSE | TUBE, 1980440C1 swing sequence valve, drain, used on models with six spool backhoe valve, if used | | | 12a | D145475 | TUBE | UBE, 1980440C1 swing sequence valve, drain, used on models with seven spool backhoe valve and models with optional rear hydraulic attachments, if used | | | | Ref. 12A tubes pass under the valve body and enter on the opposite side of the valve from the old Ref. 12. The adjustable 90 must be turned to line up. | | | | 12b | D150889 | PIPE | TUBE, 1346067C1 swing sequence valve, drain, used on models with six spool backhoe valve, if used | | | | Ref. 12B tubes pass under the valve body and enter on the opposite side of the valve from the old Ref. 12. The adjustable 90 must be turned to line up. | | | | 12c | D150896 | PIPE | TUBE, 1346067C1 swing sequence valve, drain, used on models with seven spool backhoe valve and models with optional rear hydraulic attachments, if used | | | 13 | 218-5062 | HYD CONNECTOR,7/8"-14, 37 Degree x 7/8"-14, O-Ring | ADAPTER straight, 7/8-14 inch flare x O-ring boss, Includes: Ref. 14 | | | 14 | 237-6010 | O-RING,0.097" Thk x 0.755" ID, -910, Cl 6, 90 Duro | 10-1, 90 Duro, .755" ID x .097" Thk | | | 15 | D149547 | HOSE | 550 mm long, swing section upper port to sequence valve | | | 16 | 218-5119 | ELBOW,90 Degree Elbow, 7/8" - 14 Male JIC x 1-1/16" - 12 Male ORB | 90 degree, 7/8-14 inch flare x 1-1/16-12 inch adj O-ring | | | | If straight female end of Ref. 29 hose is at backhoe valve lower port, use Ref. 16 elbow; however, if elbow end of Ref. 29 hose is at backhoe valve lower port, use Ref. 16A adapter. | | | | 16a | 218-5063 | HYD CONNECTOR,7/8" - 14 Male JIC x 1-1/16" - 12 Male ORB | ADAPTER straight, 7/8-14 flare x 1-1/16-12 inch O-ring, swing section lower port, if used, Includes: Ref. 17 | | | | If straight female end of Ref. 29 hose is at backhoe valve lower port, use Ref. 16 elbow; however, if elbow end of Ref. 29 hose is at backhoe valve lower port, use Ref. 16A adapter. | | | | 17 | 237-6012 | O-RING,0.116" Thk x 0.924" ID, -912, Cl 6, 90 Duro | 59/64 ID x 7/8 inch wide, 218-5119 or 218-5063 fitting | | | 18 | D143685 | HOSE | 633 mm long, swing sequence valve to right-hand swing cylinder closed end, Includes: Ref. 18A | | | 18a | 237-6010 | O-RING,0.097" Thk x 0.755" ID, -910, Cl 6, 90 Duro | 10-1, 90 Duro, .755" ID x .097" Thk | | | 19 | REF | INSTRUCTION | CYLINDER ASSEMBLY swing, right-hand and left-hand, for correct assembly and components, see Figure 8-124 - 8-127A | | | 20 | D31368 | HOSE | 29-3/4 inch long, swing sequence valve to right-hand swing cylinder rod end, Includes: Ref. 21 | | | 21 | 237-6010 | O-RING,0.097" Thk x 0.755" ID, -910, Cl 6, 90 Duro | 10-1, 90 Duro, .755" ID x .097" Thk | | | 22 | REF | INSTRUCTION | VALVE ASSEMBLY swing sequence, for correct assembly and components, see Figure 8-100 or 8-101A | |
|
|