| № | Номер | Название | Опции | Альт |
|---|
| 1 | D51569 | SHAFT | ROCKSHAFT - three-point hitch | | | 2 | 113-241 | BOLT,Hex, 3/8" - 16 x 3", Gr 5 | | | | 3 | 192-21 | LOCK WASHER,3/8" | WASHER, LOCK, 3/8" | | | 4 | 129-103 | NUT,Hex, 3/8" - 16, Gr 5 | NUT, 3/8"-16, G5 | | | 5 | D72875 | TUBE,23.6" L | - rockshaft, Includes: Ref. 6 | | | 6 | D50146 | BUSHING,44.68mm ID x 57.15mm OD x 38.1mm L | - tube | | | 7 | 219-1 | LUBE NIPPLE,1/8" - 27 NPTF | GREASE FITTING - straight, 1/8" NPT | | | 8 | D51299 | PIN | - mounting, tilt cylinder and strut, upper | | | 9 | D25277 | SNAP RING,23.5mm ID x 2.62mm Thk | - retaining | | | 10 | D51276 | STAND | STRUT - stationary | | | 11 | G101188 | JACK BODY | CYLINDER - tilt, parts list Figure 388 | | | 12 | D51297 | PIN | - mounting, strut, lower | | | 13 | D25277 | SNAP RING,23.5mm ID x 2.62mm Thk | - retaining, lower strut mounting pin | | | 14 | D30609 | PIN,25.4mm OD x 95.25mm L | - mounting, tilt cylinder, lower | | | 15 | 195-553 | WASHER,1", SAE | - flat, 1/2", plated, cylinder alignment | | | 16 | D25277 | SNAP RING,23.5mm ID x 2.62mm Thk | - retaining, lower tilt cylinder mounting pin | | | 17 | D51302 | PIN | - mounting, lift cylinder upper | | | 18 | D26918 | SNAP RING,#125, Ext | Ring, Snap, , upper lift cylinder mounting pin #125, Ext | | | 19 | G101189 | CYLINDER ASSY. | CYLINDER - lift, parts list Figure 386 | | | 20 | 113-257 | BOLT,Hex, 3/8" - 16 x 2-1/2", Gr 5 | | | | 21 | 192-21 | LOCK WASHER,3/8" | WASHER, LOCK, 3/8" | | | 22 | 129-103 | NUT,Hex, 3/8" - 16, Gr 5 | NUT, 3/8"-16, G5 | | | 23 | D51695 | PIN | - mounting, lift cylinder, lower | | | 24 | D51692 | SPACER | - lift cylinder mounting pin, lower | | | 25 | D51294 | PIN | - mounting, pitch cylinder at mounting frame | | | 26 | T25683 | SNAP RING,#75, Ext | Ring, Snap, , pitch cylinder mounting pin #75, Ext | | | 27 | G33128 | JACK BODY | CYLINDER - pitch, parts list Figure 390 | | | 28 | G16735 | PIN | - mounting, pitch, Serial Range: cylinder-equipment | | | 28a | T39236 | BUSHING | SPACER - to adapt G16735 pin for use with category II hitch, if used | | | 29 | A30338 | PIN | - retaining, self-locking | | | 30 | 113-257 | BOLT,Hex, 3/8" - 16 x 2-1/2", Gr 5 | | | | 31 | 192-21 | LOCK WASHER,3/8" | WASHER, LOCK, 3/8" | | | 32 | 129-103 | NUT,Hex, 3/8" - 16, Gr 5 | NUT, 3/8"-16, G5 | | | 33 | D51588 | PIVOT | BUSHING - pivot, draft arm mounting pin | | | 34 | D50724 | PIN,25.4mm OD x 160.27mm L | - mounting, draft arm to mounting frame | | | 35 | D51339 | ARM | - draft, right-hand, category I hitch, 7/8" (22 mm) pin hole | | | 36 | D51340 | ARM | - draft, left-hand, category I hitch, 7/8" (22 mm) pin hole, Includes: Ref. 37 - 39 | | | 37 | D51608 | BUSHING,25.63mm ID x 34.92mm OD x 25.4mm L | - arm, 1" (25 mm) ID | | | 38 | D51336 | BALL JOINT | BUSHING - self-aligning, 1" (25 mm) ID | | | 39 | D51557 | BALL JOINT | BUSHING - self-aligning, 7/8" (22 mm) ID | | | 40 | D99535 | ARM, LIFT | ARM - draft, right-hand, category II hitch, 1-1/8" (28 mm) pin hole | | | 41 | D99536 | ARM, LIFT | ARM - draft, left-hand, category II hitch, 1-1/8" (28 mm) pin hole, Includes: Ref. 42 - 44 | | | 42 | D51608 | BUSHING,25.63mm ID x 34.92mm OD x 25.4mm L | - arm, 1" (25 mm) ID | | | 43 | D51336 | BALL JOINT | BUSHING - self-aligning, 1" (25 mm) ID | | | 44 | H363424 | BALL JOINT | BUSHING - self-aligning, 1-1/8" (29 mm) ID | | | 45 | 113-219 | BOLT,Hex, 3/8" - 16 x 2", Gr 5 | | | | 46 | D91303 | BAR | PLATE - retainer, draft arm | | | 47 | D51722 | CASTING | RETAINER - draft arm | | | 48 | 192-21 | LOCK WASHER,3/8" | WASHER, LOCK, 3/8" | | | 49 | 25-226 | SQUARE NUT,Sq, 3/8"-16 | - square, 3/8" - 16 NC | |
|
|