| № | Номер | Название | Опции | Альт |
|---|
| L129607 | VALVE | ASSEMBLY - steering control, with internal relief, includes column, 261-1192-081 stamped on name plate, Includes: Ref. 1 - 19 | | | S301969 | VALVE | ASSEMBLY - steering control, with internal relief, no longer available, order 177285A1 on figure 5-5C, Includes: Ref. 1 - 119 | | | 1 | D51217 | BOLT,5/16" x 3 1/2" | - 12 point, special, 5/16 NF x 3-1/2 inch, used with Ref. 2 and 6, if used | | | 1a | 135866A1 | SCREW,Flg, Torx, 5/16" x 1 3/4", Gr 8 | BOLT - 12 point flange, special, 5/16 NF x 1-3/4 inch, grade 8, used with Ref. 2A and 6A, if used | | | | When the end cap repair kit is installed, "flip" outer gerotor ring, Ref. 4 and reinstall it so that the O-ring groove faces the end cap. Ref. 29, (2) N14764 plugs, shown on figure 5-5A should be replaced at the same time. | | | | 2 | D82809 | COVER | CAP - end, with o-ring groove, uses N6392 o-ring, Ref. 20, shown on figure 5-5A, upon depletion of D82809 stock, order 136492A1 repair kit, see below | | | 2a | 135867A1 | CAP | - end, without o-ring groove, uses 238-6040 o-ring, Ref. 20, shown on figure 5-5C, in the gerotor o-ring groove | | | | When the end cap repair kit is installed, "flip" outer gerotor ring, Ref. 4 and reinstall it so that the O-ring groove faces the end cap. Ref. 29, (2) N14764 plugs, shown on figure 5-5A should be replaced at the same time. | | | | 100066A1 | ROTOR | KIT - gerotor set and spacer, Includes: Ref. 3 and 4 | | | 3 | 103507A1 | SPACER | - drive shaft | | | 4 | D83219 | ROTOR | GEROTOR - set, valve, no longer available, order 100066A1 kit | | | 5 | L30878 | DRIVE SHAFT | SHAFT - drive, gerotor | | | 6 | S113037 | PLATE | - spacer, without o-ring, groove, uses N6392 o-ring, Ref. 20, shown on figure 5-5A, in the gerotor o-ring groove, upon depletion of S113037 stock, order 136493A1 repair kit, see below | | | 6a | 135869A1 | PLATE | - spacer, with o-ring groove, (install with groove facing gerotor) uses 238-6040 o-ring, Ref. 20, shown on figure 5-5C | | | | When the end cap repair kit is installed, "flip" outer gerotor ring, Ref. 4 and reinstall it so that the O-ring groove faces the end cap. Ref. 29, (2) N14764 plugs, shown on figure 5-5A should be replaced at the same time. | | | | S301971 | TESTER | CONTROL ASSEMBLY - valve, Includes: Ref. 7 - 11 | | | 7 | NSS | NOT SOLD SEPARAT | BODY - control assembly | | | 8 | NSS | NOT SOLD SEPARAT | SLEEVE - control assembly | | | 9 | L30888 | PIN | - roll | | | 10 | NSS | NOT SOLD SEPARAT | SPOOL - control assembly | | | 11 | N14250 | KIT | - centering spring, set of 6, spool | | | 12 | D82804 | RACE | - thrust, bearing | | | 13 | G13609 | THRUST BEARING,25.4mm ID x 39.67mm OD x 1.98mm W | BEARING, THRUST - Roller | | | 14 | N13312 | CYLINDER END CAP | BUSHING - spool | | | 15 | S110169 | WASHER | RING - retaining, bushing | | | 16 | D82805 | SET SCREW | SCREW - set | | | 17 | D82806 | VALVE SEAT | SEAT - ball | | | 18 | 211-1010 | BALL,5/16" OD | - chrome aloy steel, 5/16 inch, grade 245/16; 24, CRS | | | 19 | L35368 | RETAINER | - check ball | | | 136493A1 | COVER | KIT - repair, end cap and spacer plate, includes Ref. 1A, 2A and 6A, use with 238-6040 o-rings, Ref. 20, shown on figure 5-5C, Includes: Ref. 20 - 32 | | | | When the end cap repair kit is installed, "flip" outer gerotor ring, Ref. 4 and reinstall it so that the O-ring groove faces the end cap. Ref. 29, (2) N14764 plugs, shown on figure 5-5A should be replaced at the same time. | | | | S301969 | VALVE | ASSEMBLY - steering control, no longer available, order 177285A1 on figure 5-5C | | | S301023 | SEAL KIT | KIT - seal, no longer available, order 1343658C3 seal kit, shown on figure 5-5C, Includes: Ref. 20 - 27 | | | 20 | 238-5040 | O-RING,0.07" Thk x 2.864" ID, -40, Cl 5, 75 Duro | -040, 70 Duro, 2.864" ID x .070" Thk, Used with D82809 cap and S113037 plate, replaces N6392 o-ring | | | 21 | 238-5225 | O-RING,0.139" Thk x 1.859" ID, -225, Cl 5, 75 Duro | | | | 22 | 50-2703T1 | BACK-UP RING | RING - backup, seal | | | 23 | 697494R91 | OIL SEAL | SEAL - 1 inch ID | | | 24 | 238-5012 | O-RING,0.07" Thk x 0.364" ID, -12, Cl 5, 75 Duro | -012, 70 Duro, .364" ID x .070" Thk | | | 25 | L30893 | O-RING,1/16" Thk x 5/16" ID | - 5/16 ID x 1/8 inch wide, seat, inner | | | 26 | 238-5121 | O-RING,0.103" Thk x 1.049" ID, -121, Cl 5, 75 Duro | Spool, inner -121, 70 Duro, 1.049" ID x .103" Thk | | | 27 | N13313 | SEAL,25.1mm ID x 26.7mm OD x 2.6mm Thk | - teflon, inner | | | 28 | 211-1006 | BALL,3/16" Dia | - chrome alloy steel, 3/16 inch, grade 24 | | | 29 | 136494A1 | PLUG | RETAINER, spring, anticavitation, replaces N14764 plug | | | 30 | N14763 | SPRING | - anticavitation | | | 31 | S301818 | CAP | COLUMN ASSEMBLY - lower, steering, individual components are not serviced separately | | | 32 | 380-2612 | 12 PT SCREW,Flg, 3/8" - 16 x 3/4", Full Thd | SCREW - 12 point flange, chemical locking, 3/8 NC x 3/4 inch, Replaces 27588R1 | |
|
|