| № | Номер | Название | Опции | Альт |
|---|
| L127439 | AXLE, FRONT | AXLE ASSEMBLY - front, complete, Carraro No. 125822, parts list Figures 6-52 through 6-58 and 7-02 | |
| L127440 | AXLE, REAR | AXLE ASSEMBLY - rear, complete, Carraro No. 125823, parts list Figures 6-52 through 6-58 and 7-02 | |
| L128115 | AXLE | ASSEMBLY - rear, no-spin differential, parts list Figures 6-52 through 6-58 and 7-02 | |
| 1 | K395102 | OIL SEAL | - oil, hub, L127439 and L127440 axles | |
| 2 | K395101 | TAPERED BEARING,109.5mm ID x 126mm x 21.4mm L | BEARING - ball, hub | |
| 3 | D142978 | HUB | - wheel attaching | |
| 4 | A156873 | PLUG, DRAIN,M22 x 1.5 | | |
| 5 | D142979 | RING, SNAP | RING - lock | |
| 6 | D142980 | CARRIER | HUB - ring gear | |
| 7 | K395105 | RING | BUSHING - 20 mm OD, centering | |
| 7a | K395104 | RING | BUSHING - 24 mm OD, centering | |
| 8 | K395131 | BOLT,Hex, M14 x 1.5 x 65mm, Cl 10.9 | BOLT, , Special Hex, M14 x 65, Cl 10.9 | |
| 9 | D142981 | GEAR WHEEL | GEAR - ring, planetary | |
| 10 | E135789 | SHAFT | - pinion | |
| 11 | D142985 | SUN GEAR | GEAR - pinion, planetary | |
| 12 | D142984 | WASHER | - thrust, pinion gear | |
| 13 | 196089A1 | NEEDLE BEARING,Needle, 4mm OD x 34.8mm L | BEARING - needle, planetary gear (replaces K260211) | |
| 14 | K395093 | HEADED PIN,12mm OD x 15mm L | PIN - thrust | |
| 15 | D142988 | CARRIER | COVER - planetary | |
| | Ref: #15 Replaced by P/N 144659A1 Cover with 6mm holes. | | |
| | Ref: #15 Replaced by P/N E135791 Cover with 4mm holes. | | |
| | Ref # 15, 20, 21 now has part numbers for 6mm as well as 4mm roll pin parts - These parts should be matched to their related mm sizes. See below for P/N changes. W14C should only be serviced with 6mm roll pin parts. | | |
| 16 | D142986 | STUD,88mm L | - special, without collar | |
| 17 | D142987 | STUD | - special, with collar, for recessed bolt holes | |
| 18 | K395029 | SCREW | - special, planetary cover | |
| 19 | K395094 | DOWEL,M18 x 36 | Pin, Planetary cover M18 x 36 | |
| 20 | 109643A1 | LARGE PIN | SHAFT - pinion gear 6mm hole cover. (replaces D142989) | |
| | Ref # 15, 20, 21 now has part numbers for 6mm as well as 4mm roll pin parts - These parts should be matched to their related mm sizes. See below for P/N changes. W14C should only be serviced with 6mm roll pin parts. | | |
| 21 | K260197 | PIN | - split, pinion gear shaft | |
| | Ref: #21 Replaced by P/N 109642A1 Pin with 6mm O.D. (Free turning inside) | | |
| | Ref: #21 Replaced by P/N 932252R1 Pin with 4mm split roll pin. 31-May-96 | | |
| | Ref # 15, 20, 21 now has part numbers for 6mm as well as 4mm roll pin parts - These parts should be matched to their related mm sizes. See below for P/N changes. W14C should only be serviced with 6mm roll pin parts. | | |
| 22 | A27342 | O-RING,1.109" ID x 1.387" OD x 0.139" | - pinion gear shaft | |
| 23 | S301074 | COVER | PLATE - planetary cover, with CASE logo | |
| | Ref: #23 The planetary cover plate with the "CASE" logo will be eliminated from all axles. Continue to use for service of machines with the logo. | | |
| 24 | K395082 | SCREW,M8 x 20mm | - special, planetary cover plate | |
| M20704 | ADHESIVE | SEALANT - 3 oz (89 ml) of sealant in a tube, planetary cover to hub, not shown | |
