| № | Номер | Название | Опции | Альт |
|---|
| 1 | S241920 | SWITCH | - push button, cold start (replaces D34924 switch), on instrument panel | | | 2 | R52251 | ELECTRICAL WIRE | WIRE - 16-1/8 inch (410 mm) long, push button switch, to front harness pin connection | | | | Route Ref. 2 and 3 wires with front wiring harness using the same clamps and tie straps. See Figure 4-28 or 4-30 for front wiring harness routing. | | | | 3 | R52250 | ELECTRICAL WIRE | WIRE - 20 inch (510 mm) long, push button switch, to ether start valve wire | | | | Route Ref. 2 and 3 wires with front wiring harness using the same clamps and tie straps. See Figure 4-28 or 4-30 for front wiring harness routing. | | | | 4 | REF | INSTRUCTION | HARNESS - front wiring, see Figure 4-28 or 4-30 for correct harness | | | 5 | A172117 | SWITCH | THERMOCOUPLE - on engine | | | 6 | 217-45 | REDUCER,3/4" - 14 NPTF x 1/2" - 18 Fem NPTF | use on loader and 62 inch gauge long track dozer models only 3/4"-14 NPTF x 1/2"-18 Fem NPTF | | | 7 | R52849 | ELECTRICAL WIRE | WIRE - temperature switch ground, use on loader and 62 inch gauge long track dozer models only, use front harness clamp hardware | | | 8 | R52252 | ELECTRICAL WIRE | WIRE - temperature switch ground, all dozer models except 62 inch gauge long track dozer and drawbar models only, use injection pump mounting hardware | | | 9 | D36944 | TUBE | - nylon, 39-7/16 inch (1000 mm) long, cut from L60539X bulk tube, use on loader models only, see below | | | 10 | R52565 | TUBE,0.125" OD x 29.5" L | - nylon, 29-1/2 inch (750 mm) long, cut from L60539X bulk tube, use on all dozer models except 62 inch gauge long track dozer and drawbar models only, see below | | | 10a | L16688 | TUBE,0.078" ID x 0.125" OD x 32" L | - nylon, 32 inch (813 mm) long, cut from A138483 tube, use on 62 inch gauge long track dozer models only | | | 11 | 51200330 | CLAMP | - tube, P-type, 3/16 inch ID, use engine hardware | | | 12 | 80679 | LOCK WASHER,1/20.507 CST ZND | WASHER, LOCK, , Use on loader and 62" gauge long track dozer models only 1/2" | | | 13 | A172900 | NOZZLE CAP | NOZZLE ASSEMBLY - cold start injection, atomizer, component parts not serviced separately | | | 14 | 217-40 | REDUCER,1/4"-18 NPTF x 1/8"-27 Fem NPTF | - 1/4 PT x 1/8 inch PT, for dozer and drawbar models only | | | 15 | 222-615 | ELBOW,90 Degree, 5/16"-24 x 1/8" NPT, Comp | Incl. Ref 16 90º, 5/16"-24 x 1/8" NPT, Comp | | | 16 | 222-650 | SLEEVE,1/8" Tube, Comp | Tapered 1/8" Tube, Comp | | | 17 | 222-660 | FLANGE NUT,5/16"-24, 45 Degree Fl, Comp | 1/8" tube OD 5/16"-24, 45º Fl, Comp | | | 18 | A172516 | VALVE | - solenoid, starting fluid injection, 3 cc injection volume, with bracket, component parts not serviced separately, use on loader and 62 inch gauge long track dozer models only | | | 19 | A173281 | SOLENOID VALVE | VALVE ASSEMBLY - solenoid, starting fluid injection, 6 cc injection volume, with bracket, component parts not serviced separately, for all dozers except 62 inch gauge long track and drawbar models | | | 20 | A171940 | CYLINDER | - starting fluid | | | 21 | 413-516 | BOLT,Hex, 5/16" - 18 x 1", Gr 5 | - hex, 5/16 NC x 1 inch | | | 22 | 495-11034 | WASHER,5/16", SAE | 5/16" SAE (flat, 11/32 x 11/16 x 1/16") | | | 23 | 425-105 | NUT,5/16"-18, G5 | - hex, 5/16 inch NC | | | 24 | B17425 | LOCTITE | SEALANT - pipe threads, with Teflon, Loctite No. 92, 50 ml tube, use to seal the rubber boot of Ref. 1 switch | | | L60539X | TUBE | - bulk, nylon, 1/8 (3) ID x 168 inch (4267 mm) long | | | A138483 | TUBE | - bulk, nylon, 99 inch (2515 mm) long | |
|
|