| № | Номер | Название | Опции | Альт |
|---|
| D124605 | CENTER AXLE | AXLE ASSEMBLY (CARRARO 118218) - rear drive, Includes: Ref. 1 - 29 | | | | D124605 Axle Assembly includes all parts on Figure 6-36 through 6-44. | | | | 1 | N8891 | HOUSING | - swivel, axle ends | | | 2 | 3051337R1 | SEALING RING,M18 x 24mm OD x 1.5mm Thk | (Replaces seal K957001) M18 x 24 x 1.5 | | | 3 | K260137 | BLEEDER | PROTECTOR - breather (Replaces protector K957000) | | | 4 | 1966149C2 | BREATHER | axle housing (Replaces breather K965231) | | | 5 | K956999 | PLUG | CAP - breather cover (Replaces cap K260136) | | | 6 | N8898 | OIL SEAL | - oil, 170 OD x 145 ID x 16 mm wide, housing, fits outside of K261816 wear ring, Ref. 10 on Figure 6-44 used on 140 mm OD hub, Ref. 11 on Figure 6-44 | | | | N8898 oil seal and K261816 wear ring may replace an oil seal and felt seal mounted one behind the other, used on some models. | | | | 6a | N9859 | SEAL | - oil, 170 OD x 150 mm ID, housing, fits outside of Ref. 10A wear ring on Figure 6-44, used on 145 mm OD hub, Ref. 11A on Figure 6-44 | | | 7 | 905873R1 | NUT,M14 x 1.5, G8 | NUT - hex, self-locking, special (Replaces nut K965250) | | | 8 | K965249 | STUD | - hub to swivel housing | | | 9 | K965237 | GASKET | - hub to swivel housing | | | 9a | K965321 | BALL BEARING | BEARING - ball, small | | | 10 | K262149 | SHAFT | SPINDLE - planetary (Replaces spindle K965236) | | | 10a | N8892 | SLEEVE | - seal, 62 OD x 55 ID x 11 mm wide | | | 11 | K965322 | BUSHING | - spindle | | | 12 | N8897 | OIL SEAL | SEAL - oil | | | 13 | N7552 | BOLT,M14 x 50mm | BOLT - steering lever | | | 14 | 892-11014 | LOCK WASHER,14.5mm ID x 24.1mm OD x 4.5mm Thk | WASHER - lock, 14 mm | | | 15 | D126042 | ARM | LEVER - steering, right-hand | | | 16 | D126043 | ARM | LEVER - steering, left-hand | | | 17 | K965275 | PIN | - dowell | | | 18 | N7532 | PIN,60mm OD x 57mm L | - swivel | | | 19 | N7533 | SEALING RING | - pin | | | 20 | N7534 | ROLLER BEARING,30mm ID x 62mm OD x 17.25mm W | BEARING ASSEMBLY - cup and cone, tapered roller bearing, swivel pin | | | 21 | K965243 | SHIM,0.1mm Thk | | | | 22 | K965244 | SHIM,0.3mm Thk | | | | 23 | K965245 | SHIM,0.5mm Thk | | | | 23a | NSS | NOT SOLD SEPARAT | SHIM - 1.0 mm, when replacing this shim, use two K965245 shims (Ref. 23) | | | 24 | D126277 | ARM | LEVER - lower, swivel housing to tie rod ball joint, left-hand | | | 24a | D126278 | ARM | LEVER - lower, swivel housing to tie rod ball joint, right-hand | | | 25 | N7552 | BOLT,M14 x 50mm | BOLT - steering lever | | | 26 | 892-11014 | LOCK WASHER,14.5mm ID x 24.1mm OD x 4.5mm Thk | WASHER - lock, 14 mm | | | 27 | 321204 | LUBE NIPPLE,M6 x 1.0 x 16mm OAL | NIPPLE, LUBE, , Swivel pin, steering levers and covers (Replaces fitting K965246) M6 x 1, 16mm lg | | | 28 | N7527 | ADJUSTMENT SCREW | STUD - steering stop | | | 29 | K965369 | JAM NUT | - hex, special, 12 mm | |
|
|