(126) - HYDRAULIC ANGLING DOZER

№	Номер	Название	Опции
1	34044	SPACER	BRACKET - pivot, dozer attaching
2	34043	SPACER,12.95mm ID x 19.05mm OD x 17.47mm L	- pivot bracket
3	D23206	HHCS - 3/4" - 16 NF x 12-1/2"
4	92-12	LOCK WASHER,3/4"	WASHER, LOCK, 3/4"
5	25-1112	NUT,3/4"-16, G5	- hex. (3/4 - 16 NF)
6	16-12192	BOLT (MACHINE)	HHCS - 3/4 - 16 NF x 12
7	92-12	LOCK WASHER,3/4"	WASHER, LOCK, 3/4"
8	25-1112	NUT,3/4"-16, G5	- hex. (3/4 - 16 NF)
9	33961	CONNECTING LINK	PLATE - dozer rub
10	34047	LEVER	SPACER - rub plate
11	16-12192	BOLT (MACHINE)	HHCS - 3/4 - 16 NF x 12
12	92-12	LOCK WASHER,3/4"	WASHER, LOCK, 3/4"
13	25-1112	NUT,3/4"-16, G5	- hex. (3/4 - 16 NF)
14	37963	"C" FRAME - hydraulic angling dozer
15	38679		PIN - mounting, "C" frame to pivot bracket
16	38072	PIN	- pivot, moldboard
17	138-180	LOCK PIN,3/8" x 2 1/2", Slotted	PIN, 3/8" x 2 1/2", Slotted
18	37573		PLATE - slide
19	164-132	HEX SOC SCREW,Flat Hd, 1/2" - 20 x 1 3/4"	CAPSCREW - flat socket head (1/2" - 20 NF x 1-3/4")
20	39127	BRACKET	- slide
21	38070	LUBE NIPPLE	PIN - angling stop
22	D20224		STRUT - slide bracket to moldboard, R.H.
23	D20225		STRUT - slide bracket to moldboard, L.H.
24	D20247		PIN - mounting, Serial Range: strut-moldboard
25	138-142	LOCK PIN,1/4" x 2", Slotted	PIN, 1/4" x 2", Slotted
26	D28564		PIN - mounting, strut to slide bracket
27	14-812	BOLT,Hex, 1/2" - 20 x 3/4", Gr 5	HHCS - 1/2 - 20 NF x 3/4
28	193-32	LOCK WASHER,Int Tooth, 1/2"	WASHER, LOCK, Int Tooth, 1/2"
29	D23740	BUSHING	- lockhead pin
30	37932	CYLINDER - dozer angling, hydraulic (See figure 138 for breakdown)
31	33676	DRAWBAR SUPPORT	LIMIT - leaf spring
32	D20176		HOSE - bulkhead union to junction block and tube assy (1/2" I.D. x 7/8" O.D. x 15-3/4")
33	D23906	ELBOW	- street, 45 degrees (3/8" NPT)
34	39612	X	JUNCTION BLOCK AND TUBE ASSY - original equipment (Use D28039 and 221-2)
	D28039	BLOCK	JUNCTION BLOCK AND TUBE ASSY - replacement (See 39612)
	221-2	DRAIN PLUG,Sq Hd, 1/4"-18 NPTF	PLUG - pipe, 1/4" NPT square head (Not shown) See 39612
35	14-828	BOLT,Hex, 1/2" - 20 x 1-3/4", Gr 5	HHCS - 1/2 - 20 NF x 1-3/4
36	92-8	LOCK WASHER,1/2"
37	39610		GUARD - tubing, inside (Tack welded over inside tube of junction block and tube assy)
38	39611	FINGER	GUARD - tubing, outside (Tack welded over outside tube of junction block and tube assy)
39	D20141	GUARD - hose
40	D20369	CLAMP	PLATE - clamp
41	14-836	BOLT,Hex, 1/2" - 20 x 2-1/4", Gr 5	HHCS - 1/2 - 20 NF x 2-1/4
42	92-8	LOCK WASHER,1/2"
43	39607	SPACER - clamp plate
44	38614	CLIP	HOSE - junction block and tube assy to L.H. angling cylinder (1/2" I.D. x 7/8" O.D. x 12-5/8")
45	38324		TUBE - hose to L.H. angling cylinder, rear port
46	38326	BUSHING,1.875, 1.125" Length	TUBE - hose to L.H. angling cylinder, front port
47	218-493	ELBOW,90 Degree Elbow, 3/4" - 16 Male JIC x 1/2" - 14 Male NPTF	- male, 90 degrees (1/2" JIC x 1/2" NPT)
48	39637	LINE	HOSE - L.H. angling cylinder to R.H. angling cylinder (1/2" I.D. x 7/8" O.D. x 45")
49	31665	COLLAR CLAMP	PLATE - clamp
50	14-528	BOLT,Hex, 5/16" - 24 x 1-3/4", Gr 5
51	92-5	LOCK WASHER,5/16"
52	25-115	NUT,5/16"-24, G5	- hex (5/16"-24 NF)
53	38328	TUBE - hose to R.H. angling cylinder, front port
54	38322	TUBE - hose to R.H. angling cylinder, rear port
55	218-493	ELBOW,90 Degree Elbow, 3/4" - 16 Male JIC x 1/2" - 14 Male NPTF	- male, 90 degrees (1/2" JIC x 1/2" NPT)
56	31109	PIN ASSY.	PIN - mounting, angling cylinder to moldboard and "C" frame
57	14-812	BOLT,Hex, 1/2" - 20 x 3/4", Gr 5	HHCS - 1/2 - 20 NF x 3/4
58	193-32	LOCK WASHER,Int Tooth, 1/2"	WASHER, LOCK, Int Tooth, 1/2"
59	D23740	BUSHING	- lockhead pin
60	D20266		MOLDBOARD - hydraulic angling dozer
61	38047	EDGE	- cutting, center
62	16042	EDGE	- cutting, end
63	19-828	BOLT,1/2"-13 x 1 3/4", G5	- plow, no. 3 head (1/2" - 13 NC x 1-3/4")
64	92-8	LOCK WASHER,1/2"
65	25-108	NUT,1/2"-13, G5	- hex. (1/2 - 13 NC)