CASE > HEAVY EQUIPMENT > CRAWLER DOZERS > 400 > (420) - CASE CRAWLER TRACTOR (S/N 3008188 TO 3012300) (1/55-12/93) > (07) - HYDRAULIC SYSTEM > (122) - HYDRAULIC CROWN TILT BULLDOZER

№ Номер Название Опции Альт 1 37775 BAR TRUNNION - push 2 34043 SPACER,12.95mm ID x 19.05mm OD x 17.47mm L - push trunnion 3 D23206 HHCS - 3/4" - 16 NF x 12-1/2" 4 92-12 LOCK WASHER,3/4" WASHER, LOCK, 3/4" 5 25-1112 NUT,3/4"-16, G5 - hex. (3/4 - 16 NF) 6 16-12192 BOLT (MACHINE) HHCS - 3/4 - 16 NF x 12 7 92-12 LOCK WASHER,3/4" WASHER, LOCK, 3/4" 8 25-1112 NUT,3/4"-16, G5 - hex. (3/4 - 16 NF) 9 37992 PLATE - dozer rub 10 34047 LEVER SPACER - rub plate 11 16-12192 BOLT (MACHINE) HHCS - 3/4 - 16 NF x 12 12 92-12 LOCK WASHER,3/4" WASHER, LOCK, 3/4" 13 25-1112 NUT,3/4"-16, G5 - hex. (3/4 - 16 NF) 14 37881 CONDUIT PUSH BEAM - hydraulic crown tilt bulldozer, R.H. 15 37997 FORK PUSH BEAM - hydraulic crown tilt bulldozer, L.H. 16 37990 PIN - cylinder and strut to push beam, strut to moldboard, and push beam to moldboard (Inner) 17 138-178 LOCK PIN,3/8" x 2 1/4", Slotted PIN, 3/8" x 2 1/4", Slotted 18 38158 STRUT - R.H. push, Serial Range: beam-moldboard 19 39634 HOSE Guard, Crowning Cylinder, Rear 20 14-812 BOLT,Hex, 1/2" - 20 x 3/4", Gr 5 HHCS - 1/2 - 20 NF x 3/4 21 92-8 LOCK WASHER,1/2" 22 37966 GUARD - junction block and tube assy 23 14-828 BOLT,Hex, 1/2" - 20 x 1-3/4", Gr 5 HHCS - 1/2 - 20 NF x 1-3/4 24 92-8 LOCK WASHER,1/2" 25 39180 HOSE - bulkhead union to junction block and tube assy (1/2" I.D. x 7/8" O.D. x 18-3/4") 26 39577 JUNCTION BLOCK AND TUBE ASSY - original equipment (Use D28040, D23906 and 221-2) D28040 STEM JUNCTION BLOCK AND TUBE ASSY - replacement (See 39577) D23906 ELBOW - street, 90 degrees (Junction block to hose) (3/8" NPT) Not shown 221-2 DRAIN PLUG,Sq Hd, 1/4"-18 NPTF PLUG - pipe, 1/4" NPT square head (Not shown) 27 14-828 BOLT,Hex, 1/2" - 20 x 1-3/4", Gr 5 HHCS - 1/2 - 20 NF x 1-3/4 28 92-8 LOCK WASHER,1/2" 29 37965 HOSE - junction block and tube assy to tilt cylinder (1/2" I.D. x 7/8" O.D. x 19") 30 218-456 HYD CONNECTOR,3/4" - 16 Male JIC x 1/2" - 14 Male NPTF CONNECTOR - male, 1/2" JIC x 1/2" NPT 31 36801 GEAR PLATE - clamp 32 14-820 BOLT,Hex, 1/2" - 20 x 1-1/4", Gr 5 HHCS - 1/2 - 20 NF x 1-1/4 33 92-8 LOCK WASHER,1/2" 34 32978 PLATE ASSY. PLATE - clamp 35 14-528 BOLT,Hex, 5/16" - 24 x 1-3/4", Gr 5 36 92-5 LOCK WASHER,5/16" 37 25-115 NUT,5/16"-24, G5 - hex (5/16"-24 NF) 38 39618 CABLE TERMINAL TUBE - hose to rear tilt cylinder port 39 218-493 ELBOW,90 Degree Elbow, 3/4" - 16 Male JIC x 1/2" - 14 Male NPTF - male, 90 degrees (1/2" JIC x 1/2" NPT) 40 38160 LINE CYLINDER - dozer tilt, hydraulic (See figure136 for breakdown) 41 33676 DRAWBAR SUPPORT LIMIT - leaf spring 42 D21649 MOLDBOARD - hydraulic crown tilt bulldozer 43 16452 EDGE - cutting, center 44 NLS NO LONGER SERVICED EDGE - cutting, end 45 19-828 BOLT,1/2"-13 x 1 3/4", G5 - plow, no. 3 head (1/2" - 13 NC x 1-3/4") 46 92-8 LOCK WASHER,1/2" 47 25-108 NUT,1/2"-13, G5 - hex. (1/2 - 13 NC) 48 219-1 LUBE NIPPLE,1/8" - 27 NPTF FITTING - grease, straight (1/8" NPT) 49 39222 PIN - R.H. push beam to moldboard, outer 50 138-178 LOCK PIN,3/8" x 2 1/4", Slotted PIN, 3/8" x 2 1/4", Slotted 51 39631 FLEXIBLE HOSE GUARD - tilt cylinder, front 52 D20188 PIN - tilt, Serial Range: cylinder-moldboard 53 13-888 BOLT,Hex, 1/2" - 13 x 5-1/2", Gr 5 54 92-8 LOCK WASHER,1/2" 55 25-108 NUT,1/2"-13, G5 - hex. (1/2 - 13 NC) 56 D20149 PIN - L.H. push beam to moldboard, outer 57 13-896 BOLT,Hex, 1/2" - 13 x 6", Gr 5 58 16726 PIN - mounting, lift, Serial Range: cylinder-moldboard 59 132-154 COTTER PIN,1/4" x 2" Pin, Split (Cotter), 1/4" x 2" 60 39074 GUARD - hose, mounts with push trunnion